| /* | |
| * Copyright (c) 2014 Realtek Semiconductor Corp. All rights reserved. | |
| * | |
| * This program is free software; you can redistribute it and/or | |
| * modify it under the terms of the GNU General Public License | |
| * version 2 as published by the Free Software Foundation. | |
| * | |
| */ | |
| #include <linux/signal.h> | |
| #include <linux/slab.h> | |
| #include <linux/module.h> | |
| #include <linux/netdevice.h> | |
| #include <linux/etherdevice.h> | |
| #include <linux/mii.h> | |
| #include <linux/ethtool.h> | |
| #include <linux/usb.h> | |
| #include <linux/crc32.h> | |
| #include <linux/if_vlan.h> | |
| #include <linux/uaccess.h> | |
| #include <linux/list.h> | |
| #include <linux/ip.h> | |
| #include <linux/ipv6.h> | |
| #include <net/ip6_checksum.h> | |
| #include <uapi/linux/mdio.h> | |
| #include <linux/mdio.h> | |
| #include <linux/usb/cdc.h> | |
| /* Information for net-next */ | |
| #define NETNEXT_VERSION "08" | |
| /* Information for net */ | |
| #define NET_VERSION "2" | |
| #define DRIVER_VERSION "v1." NETNEXT_VERSION "." NET_VERSION | |
| #define DRIVER_AUTHOR "Realtek linux nic maintainers <nic_swsd@realtek.com>" | |
| #define DRIVER_DESC "Realtek RTL8152/RTL8153 Based USB Ethernet Adapters" | |
| #define MODULENAME "r8152" | |
| #define R8152_PHY_ID 32 | |
| #define PLA_IDR 0xc000 | |
| #define PLA_RCR 0xc010 | |
| #define PLA_RMS 0xc016 | |
| #define PLA_RXFIFO_CTRL0 0xc0a0 | |
| #define PLA_RXFIFO_CTRL1 0xc0a4 | |
| #define PLA_RXFIFO_CTRL2 0xc0a8 | |
| #define PLA_DMY_REG0 0xc0b0 | |
| #define PLA_FMC 0xc0b4 | |
| #define PLA_CFG_WOL 0xc0b6 | |
| #define PLA_TEREDO_CFG 0xc0bc | |
| #define PLA_MAR 0xcd00 | |
| #define PLA_BACKUP 0xd000 | |
| #define PAL_BDC_CR 0xd1a0 | |
| #define PLA_TEREDO_TIMER 0xd2cc | |
| #define PLA_REALWOW_TIMER 0xd2e8 | |
| #define PLA_LEDSEL 0xdd90 | |
| #define PLA_LED_FEATURE 0xdd92 | |
| #define PLA_PHYAR 0xde00 | |
| #define PLA_BOOT_CTRL 0xe004 | |
| #define PLA_GPHY_INTR_IMR 0xe022 | |
| #define PLA_EEE_CR 0xe040 | |
| #define PLA_EEEP_CR 0xe080 | |
| #define PLA_MAC_PWR_CTRL 0xe0c0 | |
| #define PLA_MAC_PWR_CTRL2 0xe0ca | |
| #define PLA_MAC_PWR_CTRL3 0xe0cc | |
| #define PLA_MAC_PWR_CTRL4 0xe0ce | |
| #define PLA_WDT6_CTRL 0xe428 | |
| #define PLA_TCR0 0xe610 | |
| #define PLA_TCR1 0xe612 | |
| #define PLA_MTPS 0xe615 | |
| #define PLA_TXFIFO_CTRL 0xe618 | |
| #define PLA_RSTTALLY 0xe800 | |
| #define PLA_CR 0xe813 | |
| #define PLA_CRWECR 0xe81c | |
| #define PLA_CONFIG12 0xe81e /* CONFIG1, CONFIG2 */ | |
| #define PLA_CONFIG34 0xe820 /* CONFIG3, CONFIG4 */ | |
| #define PLA_CONFIG5 0xe822 | |
| #define PLA_PHY_PWR 0xe84c | |
| #define PLA_OOB_CTRL 0xe84f | |
| #define PLA_CPCR 0xe854 | |
| #define PLA_MISC_0 0xe858 | |
| #define PLA_MISC_1 0xe85a | |
| #define PLA_OCP_GPHY_BASE 0xe86c | |
| #define PLA_TALLYCNT 0xe890 | |
| #define PLA_SFF_STS_7 0xe8de | |
| #define PLA_PHYSTATUS 0xe908 | |
| #define PLA_BP_BA 0xfc26 | |
| #define PLA_BP_0 0xfc28 | |
| #define PLA_BP_1 0xfc2a | |
| #define PLA_BP_2 0xfc2c | |
| #define PLA_BP_3 0xfc2e | |
| #define PLA_BP_4 0xfc30 | |
| #define PLA_BP_5 0xfc32 | |
| #define PLA_BP_6 0xfc34 | |
| #define PLA_BP_7 0xfc36 | |
| #define PLA_BP_EN 0xfc38 | |
| #define USB_USB2PHY 0xb41e | |
| #define USB_SSPHYLINK2 0xb428 | |
| #define USB_U2P3_CTRL 0xb460 | |
| #define USB_CSR_DUMMY1 0xb464 | |
| #define USB_CSR_DUMMY2 0xb466 | |
| #define USB_DEV_STAT 0xb808 | |
| #define USB_CONNECT_TIMER 0xcbf8 | |
| #define USB_BURST_SIZE 0xcfc0 | |
| #define USB_USB_CTRL 0xd406 | |
| #define USB_PHY_CTRL 0xd408 | |
| #define USB_TX_AGG 0xd40a | |
| #define USB_RX_BUF_TH 0xd40c | |
| #define USB_USB_TIMER 0xd428 | |
| #define USB_RX_EARLY_TIMEOUT 0xd42c | |
| #define USB_RX_EARLY_SIZE 0xd42e | |
| #define USB_PM_CTRL_STATUS 0xd432 | |
| #define USB_TX_DMA 0xd434 | |
| #define USB_TOLERANCE 0xd490 | |
| #define USB_LPM_CTRL 0xd41a | |
| #define USB_UPS_CTRL 0xd800 | |
| #define USB_MISC_0 0xd81a | |
| #define USB_POWER_CUT 0xd80a | |
| #define USB_AFE_CTRL2 0xd824 | |
| #define USB_WDT11_CTRL 0xe43c | |
| #define USB_BP_BA 0xfc26 | |
| #define USB_BP_0 0xfc28 | |
| #define USB_BP_1 0xfc2a | |
| #define USB_BP_2 0xfc2c | |
| #define USB_BP_3 0xfc2e | |
| #define USB_BP_4 0xfc30 | |
| #define USB_BP_5 0xfc32 | |
| #define USB_BP_6 0xfc34 | |
| #define USB_BP_7 0xfc36 | |
| #define USB_BP_EN 0xfc38 | |
| /* OCP Registers */ | |
| #define OCP_ALDPS_CONFIG 0x2010 | |
| #define OCP_EEE_CONFIG1 0x2080 | |
| #define OCP_EEE_CONFIG2 0x2092 | |
| #define OCP_EEE_CONFIG3 0x2094 | |
| #define OCP_BASE_MII 0xa400 | |
| #define OCP_EEE_AR 0xa41a | |
| #define OCP_EEE_DATA 0xa41c | |
| #define OCP_PHY_STATUS 0xa420 | |
| #define OCP_POWER_CFG 0xa430 | |
| #define OCP_EEE_CFG 0xa432 | |
| #define OCP_SRAM_ADDR 0xa436 | |
| #define OCP_SRAM_DATA 0xa438 | |
| #define OCP_DOWN_SPEED 0xa442 | |
| #define OCP_EEE_ABLE 0xa5c4 | |
| #define OCP_EEE_ADV 0xa5d0 | |
| #define OCP_EEE_LPABLE 0xa5d2 | |
| #define OCP_PHY_STATE 0xa708 /* nway state for 8153 */ | |
| #define OCP_ADC_CFG 0xbc06 | |
| /* SRAM Register */ | |
| #define SRAM_LPF_CFG 0x8012 | |
| #define SRAM_10M_AMP1 0x8080 | |
| #define SRAM_10M_AMP2 0x8082 | |
| #define SRAM_IMPEDANCE 0x8084 | |
| /* PLA_RCR */ | |
| #define RCR_AAP 0x00000001 | |
| #define RCR_APM 0x00000002 | |
| #define RCR_AM 0x00000004 | |
| #define RCR_AB 0x00000008 | |
| #define RCR_ACPT_ALL (RCR_AAP | RCR_APM | RCR_AM | RCR_AB) | |
| /* PLA_RXFIFO_CTRL0 */ | |
| #define RXFIFO_THR1_NORMAL 0x00080002 | |
| #define RXFIFO_THR1_OOB 0x01800003 | |
| /* PLA_RXFIFO_CTRL1 */ | |
| #define RXFIFO_THR2_FULL 0x00000060 | |
| #define RXFIFO_THR2_HIGH 0x00000038 | |
| #define RXFIFO_THR2_OOB 0x0000004a | |
| #define RXFIFO_THR2_NORMAL 0x00a0 | |
| /* PLA_RXFIFO_CTRL2 */ | |
| #define RXFIFO_THR3_FULL 0x00000078 | |
| #define RXFIFO_THR3_HIGH 0x00000048 | |
| #define RXFIFO_THR3_OOB 0x0000005a | |
| #define RXFIFO_THR3_NORMAL 0x0110 | |
| /* PLA_TXFIFO_CTRL */ | |
| #define TXFIFO_THR_NORMAL 0x00400008 | |
| #define TXFIFO_THR_NORMAL2 0x01000008 | |
| /* PLA_DMY_REG0 */ | |
| #define ECM_ALDPS 0x0002 | |
| /* PLA_FMC */ | |
| #define FMC_FCR_MCU_EN 0x0001 | |
| /* PLA_EEEP_CR */ | |
| #define EEEP_CR_EEEP_TX 0x0002 | |
| /* PLA_WDT6_CTRL */ | |
| #define WDT6_SET_MODE 0x0010 | |
| /* PLA_TCR0 */ | |
| #define TCR0_TX_EMPTY 0x0800 | |
| #define TCR0_AUTO_FIFO 0x0080 | |
| /* PLA_TCR1 */ | |
| #define VERSION_MASK 0x7cf0 | |
| /* PLA_MTPS */ | |
| #define MTPS_JUMBO (12 * 1024 / 64) | |
| #define MTPS_DEFAULT (6 * 1024 / 64) | |
| /* PLA_RSTTALLY */ | |
| #define TALLY_RESET 0x0001 | |
| /* PLA_CR */ | |
| #define CR_RST 0x10 | |
| #define CR_RE 0x08 | |
| #define CR_TE 0x04 | |
| /* PLA_CRWECR */ | |
| #define CRWECR_NORAML 0x00 | |
| #define CRWECR_CONFIG 0xc0 | |
| /* PLA_OOB_CTRL */ | |
| #define NOW_IS_OOB 0x80 | |
| #define TXFIFO_EMPTY 0x20 | |
| #define RXFIFO_EMPTY 0x10 | |
| #define LINK_LIST_READY 0x02 | |
| #define DIS_MCU_CLROOB 0x01 | |
| #define FIFO_EMPTY (TXFIFO_EMPTY | RXFIFO_EMPTY) | |
| /* PLA_MISC_1 */ | |
| #define RXDY_GATED_EN 0x0008 | |
| /* PLA_SFF_STS_7 */ | |
| #define RE_INIT_LL 0x8000 | |
| #define MCU_BORW_EN 0x4000 | |
| /* PLA_CPCR */ | |
| #define CPCR_RX_VLAN 0x0040 | |
| /* PLA_CFG_WOL */ | |
| #define MAGIC_EN 0x0001 | |
| /* PLA_TEREDO_CFG */ | |
| #define TEREDO_SEL 0x8000 | |
| #define TEREDO_WAKE_MASK 0x7f00 | |
| #define TEREDO_RS_EVENT_MASK 0x00fe | |
| #define OOB_TEREDO_EN 0x0001 | |
| /* PAL_BDC_CR */ | |
| #define ALDPS_PROXY_MODE 0x0001 | |
| /* PLA_CONFIG34 */ | |
| #define LINK_ON_WAKE_EN 0x0010 | |
| #define LINK_OFF_WAKE_EN 0x0008 | |
| /* PLA_CONFIG5 */ | |
| #define BWF_EN 0x0040 | |
| #define MWF_EN 0x0020 | |
| #define UWF_EN 0x0010 | |
| #define LAN_WAKE_EN 0x0002 | |
| /* PLA_LED_FEATURE */ | |
| #define LED_MODE_MASK 0x0700 | |
| /* PLA_PHY_PWR */ | |
| #define TX_10M_IDLE_EN 0x0080 | |
| #define PFM_PWM_SWITCH 0x0040 | |
| /* PLA_MAC_PWR_CTRL */ | |
| #define D3_CLK_GATED_EN 0x00004000 | |
| #define MCU_CLK_RATIO 0x07010f07 | |
| #define MCU_CLK_RATIO_MASK 0x0f0f0f0f | |
| #define ALDPS_SPDWN_RATIO 0x0f87 | |
| /* PLA_MAC_PWR_CTRL2 */ | |
| #define EEE_SPDWN_RATIO 0x8007 | |
| /* PLA_MAC_PWR_CTRL3 */ | |
| #define PKT_AVAIL_SPDWN_EN 0x0100 | |
| #define SUSPEND_SPDWN_EN 0x0004 | |
| #define U1U2_SPDWN_EN 0x0002 | |
| #define L1_SPDWN_EN 0x0001 | |
| /* PLA_MAC_PWR_CTRL4 */ | |
| #define PWRSAVE_SPDWN_EN 0x1000 | |
| #define RXDV_SPDWN_EN 0x0800 | |
| #define TX10MIDLE_EN 0x0100 | |
| #define TP100_SPDWN_EN 0x0020 | |
| #define TP500_SPDWN_EN 0x0010 | |
| #define TP1000_SPDWN_EN 0x0008 | |
| #define EEE_SPDWN_EN 0x0001 | |
| /* PLA_GPHY_INTR_IMR */ | |
| #define GPHY_STS_MSK 0x0001 | |
| #define SPEED_DOWN_MSK 0x0002 | |
| #define SPDWN_RXDV_MSK 0x0004 | |
| #define SPDWN_LINKCHG_MSK 0x0008 | |
| /* PLA_PHYAR */ | |
| #define PHYAR_FLAG 0x80000000 | |
| /* PLA_EEE_CR */ | |
| #define EEE_RX_EN 0x0001 | |
| #define EEE_TX_EN 0x0002 | |
| /* PLA_BOOT_CTRL */ | |
| #define AUTOLOAD_DONE 0x0002 | |
| /* USB_USB2PHY */ | |
| #define USB2PHY_SUSPEND 0x0001 | |
| #define USB2PHY_L1 0x0002 | |
| /* USB_SSPHYLINK2 */ | |
| #define pwd_dn_scale_mask 0x3ffe | |
| #define pwd_dn_scale(x) ((x) << 1) | |
| /* USB_CSR_DUMMY1 */ | |
| #define DYNAMIC_BURST 0x0001 | |
| /* USB_CSR_DUMMY2 */ | |
| #define EP4_FULL_FC 0x0001 | |
| /* USB_DEV_STAT */ | |
| #define STAT_SPEED_MASK 0x0006 | |
| #define STAT_SPEED_HIGH 0x0000 | |
| #define STAT_SPEED_FULL 0x0002 | |
| /* USB_TX_AGG */ | |
| #define TX_AGG_MAX_THRESHOLD 0x03 | |
| /* USB_RX_BUF_TH */ | |
| #define RX_THR_SUPPER 0x0c350180 | |
| #define RX_THR_HIGH 0x7a120180 | |
| #define RX_THR_SLOW 0xffff0180 | |
| /* USB_TX_DMA */ | |
| #define TEST_MODE_DISABLE 0x00000001 | |
| #define TX_SIZE_ADJUST1 0x00000100 | |
| /* USB_UPS_CTRL */ | |
| #define POWER_CUT 0x0100 | |
| /* USB_PM_CTRL_STATUS */ | |
| #define RESUME_INDICATE 0x0001 | |
| /* USB_USB_CTRL */ | |
| #define RX_AGG_DISABLE 0x0010 | |
| #define RX_ZERO_EN 0x0080 | |
| /* USB_U2P3_CTRL */ | |
| #define U2P3_ENABLE 0x0001 | |
| /* USB_POWER_CUT */ | |
| #define PWR_EN 0x0001 | |
| #define PHASE2_EN 0x0008 | |
| /* USB_MISC_0 */ | |
| #define PCUT_STATUS 0x0001 | |
| /* USB_RX_EARLY_TIMEOUT */ | |
| #define COALESCE_SUPER 85000U | |
| #define COALESCE_HIGH 250000U | |
| #define COALESCE_SLOW 524280U | |
| /* USB_WDT11_CTRL */ | |
| #define TIMER11_EN 0x0001 | |
| /* USB_LPM_CTRL */ | |
| /* bit 4 ~ 5: fifo empty boundary */ | |
| #define FIFO_EMPTY_1FB 0x30 /* 0x1fb * 64 = 32448 bytes */ | |
| /* bit 2 ~ 3: LMP timer */ | |
| #define LPM_TIMER_MASK 0x0c | |
| #define LPM_TIMER_500MS 0x04 /* 500 ms */ | |
| #define LPM_TIMER_500US 0x0c /* 500 us */ | |
| #define ROK_EXIT_LPM 0x02 | |
| /* USB_AFE_CTRL2 */ | |
| #define SEN_VAL_MASK 0xf800 | |
| #define SEN_VAL_NORMAL 0xa000 | |
| #define SEL_RXIDLE 0x0100 | |
| /* OCP_ALDPS_CONFIG */ | |
| #define ENPWRSAVE 0x8000 | |
| #define ENPDNPS 0x0200 | |
| #define LINKENA 0x0100 | |
| #define DIS_SDSAVE 0x0010 | |
| /* OCP_PHY_STATUS */ | |
| #define PHY_STAT_MASK 0x0007 | |
| #define PHY_STAT_LAN_ON 3 | |
| #define PHY_STAT_PWRDN 5 | |
| /* OCP_POWER_CFG */ | |
| #define EEE_CLKDIV_EN 0x8000 | |
| #define EN_ALDPS 0x0004 | |
| #define EN_10M_PLLOFF 0x0001 | |
| /* OCP_EEE_CONFIG1 */ | |
| #define RG_TXLPI_MSK_HFDUP 0x8000 | |
| #define RG_MATCLR_EN 0x4000 | |
| #define EEE_10_CAP 0x2000 | |
| #define EEE_NWAY_EN 0x1000 | |
| #define TX_QUIET_EN 0x0200 | |
| #define RX_QUIET_EN 0x0100 | |
| #define sd_rise_time_mask 0x0070 | |
| #define sd_rise_time(x) (min(x, 7) << 4) /* bit 4 ~ 6 */ | |
| #define RG_RXLPI_MSK_HFDUP 0x0008 | |
| #define SDFALLTIME 0x0007 /* bit 0 ~ 2 */ | |
| /* OCP_EEE_CONFIG2 */ | |
| #define RG_LPIHYS_NUM 0x7000 /* bit 12 ~ 15 */ | |
| #define RG_DACQUIET_EN 0x0400 | |
| #define RG_LDVQUIET_EN 0x0200 | |
| #define RG_CKRSEL 0x0020 | |
| #define RG_EEEPRG_EN 0x0010 | |
| /* OCP_EEE_CONFIG3 */ | |
| #define fast_snr_mask 0xff80 | |
| #define fast_snr(x) (min(x, 0x1ff) << 7) /* bit 7 ~ 15 */ | |
| #define RG_LFS_SEL 0x0060 /* bit 6 ~ 5 */ | |
| #define MSK_PH 0x0006 /* bit 0 ~ 3 */ | |
| /* OCP_EEE_AR */ | |
| /* bit[15:14] function */ | |
| #define FUN_ADDR 0x0000 | |
| #define FUN_DATA 0x4000 | |
| /* bit[4:0] device addr */ | |
| /* OCP_EEE_CFG */ | |
| #define CTAP_SHORT_EN 0x0040 | |
| #define EEE10_EN 0x0010 | |
| /* OCP_DOWN_SPEED */ | |
| #define EN_10M_BGOFF 0x0080 | |
| /* OCP_PHY_STATE */ | |
| #define TXDIS_STATE 0x01 | |
| #define ABD_STATE 0x02 | |
| /* OCP_ADC_CFG */ | |
| #define CKADSEL_L 0x0100 | |
| #define ADC_EN 0x0080 | |
| #define EN_EMI_L 0x0040 | |
| /* SRAM_LPF_CFG */ | |
| #define LPF_AUTO_TUNE 0x8000 | |
| /* SRAM_10M_AMP1 */ | |
| #define GDAC_IB_UPALL 0x0008 | |
| /* SRAM_10M_AMP2 */ | |
| #define AMP_DN 0x0200 | |
| /* SRAM_IMPEDANCE */ | |
| #define RX_DRIVING_MASK 0x6000 | |
| enum rtl_register_content { | |
| _1000bps = 0x10, | |
| _100bps = 0x08, | |
| _10bps = 0x04, | |
| LINK_STATUS = 0x02, | |
| FULL_DUP = 0x01, | |
| }; | |
| #define RTL8152_MAX_TX 4 | |
| #define RTL8152_MAX_RX 10 | |
| #define INTBUFSIZE 2 | |
| #define CRC_SIZE 4 | |
| #define TX_ALIGN 4 | |
| #define RX_ALIGN 8 | |
| #define INTR_LINK 0x0004 | |
| #define RTL8152_REQT_READ 0xc0 | |
| #define RTL8152_REQT_WRITE 0x40 | |
| #define RTL8152_REQ_GET_REGS 0x05 | |
| #define RTL8152_REQ_SET_REGS 0x05 | |
| #define BYTE_EN_DWORD 0xff | |
| #define BYTE_EN_WORD 0x33 | |
| #define BYTE_EN_BYTE 0x11 | |
| #define BYTE_EN_SIX_BYTES 0x3f | |
| #define BYTE_EN_START_MASK 0x0f | |
| #define BYTE_EN_END_MASK 0xf0 | |
| #define RTL8153_MAX_PACKET 9216 /* 9K */ | |
| #define RTL8153_MAX_MTU (RTL8153_MAX_PACKET - VLAN_ETH_HLEN - VLAN_HLEN) | |
| #define RTL8152_RMS (VLAN_ETH_FRAME_LEN + VLAN_HLEN) | |
| #define RTL8153_RMS RTL8153_MAX_PACKET | |
| #define RTL8152_TX_TIMEOUT (5 * HZ) | |
| #define RTL8152_NAPI_WEIGHT 64 | |
| /* rtl8152 flags */ | |
| enum rtl8152_flags { | |
| RTL8152_UNPLUG = 0, | |
| RTL8152_SET_RX_MODE, | |
| WORK_ENABLE, | |
| RTL8152_LINK_CHG, | |
| SELECTIVE_SUSPEND, | |
| PHY_RESET, | |
| SCHEDULE_NAPI, | |
| }; | |
| /* Define these values to match your device */ | |
| #define VENDOR_ID_REALTEK 0x0bda | |
| #define VENDOR_ID_SAMSUNG 0x04e8 | |
| #define VENDOR_ID_LENOVO 0x17ef | |
| #define VENDOR_ID_NVIDIA 0x0955 | |
| #define MCU_TYPE_PLA 0x0100 | |
| #define MCU_TYPE_USB 0x0000 | |
| struct tally_counter { | |
| __le64 tx_packets; | |
| __le64 rx_packets; | |
| __le64 tx_errors; | |
| __le32 rx_errors; | |
| __le16 rx_missed; | |
| __le16 align_errors; | |
| __le32 tx_one_collision; | |
| __le32 tx_multi_collision; | |
| __le64 rx_unicast; | |
| __le64 rx_broadcast; | |
| __le32 rx_multicast; | |
| __le16 tx_aborted; | |
| __le16 tx_underrun; | |
| }; | |
| struct rx_desc { | |
| __le32 opts1; | |
| #define RX_LEN_MASK 0x7fff | |
| __le32 opts2; | |
| #define RD_UDP_CS BIT(23) | |
| #define RD_TCP_CS BIT(22) | |
| #define RD_IPV6_CS BIT(20) | |
| #define RD_IPV4_CS BIT(19) | |
| __le32 opts3; | |
| #define IPF BIT(23) /* IP checksum fail */ | |
| #define UDPF BIT(22) /* UDP checksum fail */ | |
| #define TCPF BIT(21) /* TCP checksum fail */ | |
| #define RX_VLAN_TAG BIT(16) | |
| __le32 opts4; | |
| __le32 opts5; | |
| __le32 opts6; | |
| }; | |
| struct tx_desc { | |
| __le32 opts1; | |
| #define TX_FS BIT(31) /* First segment of a packet */ | |
| #define TX_LS BIT(30) /* Final segment of a packet */ | |
| #define GTSENDV4 BIT(28) | |
| #define GTSENDV6 BIT(27) | |
| #define GTTCPHO_SHIFT 18 | |
| #define GTTCPHO_MAX 0x7fU | |
| #define TX_LEN_MAX 0x3ffffU | |
| __le32 opts2; | |
| #define UDP_CS BIT(31) /* Calculate UDP/IP checksum */ | |
| #define TCP_CS BIT(30) /* Calculate TCP/IP checksum */ | |
| #define IPV4_CS BIT(29) /* Calculate IPv4 checksum */ | |
| #define IPV6_CS BIT(28) /* Calculate IPv6 checksum */ | |
| #define MSS_SHIFT 17 | |
| #define MSS_MAX 0x7ffU | |
| #define TCPHO_SHIFT 17 | |
| #define TCPHO_MAX 0x7ffU | |
| #define TX_VLAN_TAG BIT(16) | |
| }; | |
| struct r8152; | |
| struct rx_agg { | |
| struct list_head list; | |
| struct urb *urb; | |
| struct r8152 *context; | |
| void *buffer; | |
| void *head; | |
| }; | |
| struct tx_agg { | |
| struct list_head list; | |
| struct urb *urb; | |
| struct r8152 *context; | |
| void *buffer; | |
| void *head; | |
| u32 skb_num; | |
| u32 skb_len; | |
| }; | |
| struct r8152 { | |
| unsigned long flags; | |
| struct usb_device *udev; | |
| struct napi_struct napi; | |
| struct usb_interface *intf; | |
| struct net_device *netdev; | |
| struct urb *intr_urb; | |
| struct tx_agg tx_info[RTL8152_MAX_TX]; | |
| struct rx_agg rx_info[RTL8152_MAX_RX]; | |
| struct list_head rx_done, tx_free; | |
| struct sk_buff_head tx_queue, rx_queue; | |
| spinlock_t rx_lock, tx_lock; | |
| struct delayed_work schedule; | |
| struct mii_if_info mii; | |
| struct mutex control; /* use for hw setting */ | |
| struct rtl_ops { | |
| void (*init)(struct r8152 *); | |
| int (*enable)(struct r8152 *); | |
| void (*disable)(struct r8152 *); | |
| void (*up)(struct r8152 *); | |
| void (*down)(struct r8152 *); | |
| void (*unload)(struct r8152 *); | |
| int (*eee_get)(struct r8152 *, struct ethtool_eee *); | |
| int (*eee_set)(struct r8152 *, struct ethtool_eee *); | |
| bool (*in_nway)(struct r8152 *); | |
| } rtl_ops; | |
| int intr_interval; | |
| u32 saved_wolopts; | |
| u32 msg_enable; | |
| u32 tx_qlen; | |
| u32 coalesce; | |
| u16 ocp_base; | |
| u8 *intr_buff; | |
| u8 version; | |
| }; | |
| enum rtl_version { | |
| RTL_VER_UNKNOWN = 0, | |
| RTL_VER_01, | |
| RTL_VER_02, | |
| RTL_VER_03, | |
| RTL_VER_04, | |
| RTL_VER_05, | |
| RTL_VER_06, | |
| RTL_VER_MAX | |
| }; | |
| enum tx_csum_stat { | |
| TX_CSUM_SUCCESS = 0, | |
| TX_CSUM_TSO, | |
| TX_CSUM_NONE | |
| }; | |
| /* Maximum number of multicast addresses to filter (vs. Rx-all-multicast). | |
| * The RTL chips use a 64 element hash table based on the Ethernet CRC. | |
| */ | |
| static const int multicast_filter_limit = 32; | |
| static unsigned int agg_buf_sz = 16384; | |
| #define RTL_LIMITED_TSO_SIZE (agg_buf_sz - sizeof(struct tx_desc) - \ | |
| VLAN_ETH_HLEN - VLAN_HLEN) | |
| static | |
| int get_registers(struct r8152 *tp, u16 value, u16 index, u16 size, void *data) | |
| { | |
| int ret; | |
| void *tmp; | |
| tmp = kmalloc(size, GFP_KERNEL); | |
| if (!tmp) | |
| return -ENOMEM; | |
| ret = usb_control_msg(tp->udev, usb_rcvctrlpipe(tp->udev, 0), | |
| RTL8152_REQ_GET_REGS, RTL8152_REQT_READ, | |
| value, index, tmp, size, 500); | |
| memcpy(data, tmp, size); | |
| kfree(tmp); | |
| return ret; | |
| } | |
| static | |
| int set_registers(struct r8152 *tp, u16 value, u16 index, u16 size, void *data) | |
| { | |
| int ret; | |
| void *tmp; | |
| tmp = kmemdup(data, size, GFP_KERNEL); | |
| if (!tmp) | |
| return -ENOMEM; | |
| ret = usb_control_msg(tp->udev, usb_sndctrlpipe(tp->udev, 0), | |
| RTL8152_REQ_SET_REGS, RTL8152_REQT_WRITE, | |
| value, index, tmp, size, 500); | |
| kfree(tmp); | |
| return ret; | |
| } | |
| static int generic_ocp_read(struct r8152 *tp, u16 index, u16 size, | |
| void *data, u16 type) | |
| { | |
| u16 limit = 64; | |
| int ret = 0; | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags)) | |
| return -ENODEV; | |
| /* both size and indix must be 4 bytes align */ | |
| if ((size & 3) || !size || (index & 3) || !data) | |
| return -EPERM; | |
| if ((u32)index + (u32)size > 0xffff) | |
| return -EPERM; | |
| while (size) { | |
| if (size > limit) { | |
| ret = get_registers(tp, index, type, limit, data); | |
| if (ret < 0) | |
| break; | |
| index += limit; | |
| data += limit; | |
| size -= limit; | |
| } else { | |
| ret = get_registers(tp, index, type, size, data); | |
| if (ret < 0) | |
| break; | |
| index += size; | |
| data += size; | |
| size = 0; | |
| break; | |
| } | |
| } | |
| if (ret == -ENODEV) | |
| set_bit(RTL8152_UNPLUG, &tp->flags); | |
| return ret; | |
| } | |
| static int generic_ocp_write(struct r8152 *tp, u16 index, u16 byteen, | |
| u16 size, void *data, u16 type) | |
| { | |
| int ret; | |
| u16 byteen_start, byteen_end, byen; | |
| u16 limit = 512; | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags)) | |
| return -ENODEV; | |
| /* both size and indix must be 4 bytes align */ | |
| if ((size & 3) || !size || (index & 3) || !data) | |
| return -EPERM; | |
| if ((u32)index + (u32)size > 0xffff) | |
| return -EPERM; | |
| byteen_start = byteen & BYTE_EN_START_MASK; | |
| byteen_end = byteen & BYTE_EN_END_MASK; | |
| byen = byteen_start | (byteen_start << 4); | |
| ret = set_registers(tp, index, type | byen, 4, data); | |
| if (ret < 0) | |
| goto error1; | |
| index += 4; | |
| data += 4; | |
| size -= 4; | |
| if (size) { | |
| size -= 4; | |
| while (size) { | |
| if (size > limit) { | |
| ret = set_registers(tp, index, | |
| type | BYTE_EN_DWORD, | |
| limit, data); | |
| if (ret < 0) | |
| goto error1; | |
| index += limit; | |
| data += limit; | |
| size -= limit; | |
| } else { | |
| ret = set_registers(tp, index, | |
| type | BYTE_EN_DWORD, | |
| size, data); | |
| if (ret < 0) | |
| goto error1; | |
| index += size; | |
| data += size; | |
| size = 0; | |
| break; | |
| } | |
| } | |
| byen = byteen_end | (byteen_end >> 4); | |
| ret = set_registers(tp, index, type | byen, 4, data); | |
| if (ret < 0) | |
| goto error1; | |
| } | |
| error1: | |
| if (ret == -ENODEV) | |
| set_bit(RTL8152_UNPLUG, &tp->flags); | |
| return ret; | |
| } | |
| static inline | |
| int pla_ocp_read(struct r8152 *tp, u16 index, u16 size, void *data) | |
| { | |
| return generic_ocp_read(tp, index, size, data, MCU_TYPE_PLA); | |
| } | |
| static inline | |
| int pla_ocp_write(struct r8152 *tp, u16 index, u16 byteen, u16 size, void *data) | |
| { | |
| return generic_ocp_write(tp, index, byteen, size, data, MCU_TYPE_PLA); | |
| } | |
| static inline | |
| int usb_ocp_read(struct r8152 *tp, u16 index, u16 size, void *data) | |
| { | |
| return generic_ocp_read(tp, index, size, data, MCU_TYPE_USB); | |
| } | |
| static inline | |
| int usb_ocp_write(struct r8152 *tp, u16 index, u16 byteen, u16 size, void *data) | |
| { | |
| return generic_ocp_write(tp, index, byteen, size, data, MCU_TYPE_USB); | |
| } | |
| static u32 ocp_read_dword(struct r8152 *tp, u16 type, u16 index) | |
| { | |
| __le32 data; | |
| generic_ocp_read(tp, index, sizeof(data), &data, type); | |
| return __le32_to_cpu(data); | |
| } | |
| static void ocp_write_dword(struct r8152 *tp, u16 type, u16 index, u32 data) | |
| { | |
| __le32 tmp = __cpu_to_le32(data); | |
| generic_ocp_write(tp, index, BYTE_EN_DWORD, sizeof(tmp), &tmp, type); | |
| } | |
| static u16 ocp_read_word(struct r8152 *tp, u16 type, u16 index) | |
| { | |
| u32 data; | |
| __le32 tmp; | |
| u8 shift = index & 2; | |
| index &= ~3; | |
| generic_ocp_read(tp, index, sizeof(tmp), &tmp, type); | |
| data = __le32_to_cpu(tmp); | |
| data >>= (shift * 8); | |
| data &= 0xffff; | |
| return (u16)data; | |
| } | |
| static void ocp_write_word(struct r8152 *tp, u16 type, u16 index, u32 data) | |
| { | |
| u32 mask = 0xffff; | |
| __le32 tmp; | |
| u16 byen = BYTE_EN_WORD; | |
| u8 shift = index & 2; | |
| data &= mask; | |
| if (index & 2) { | |
| byen <<= shift; | |
| mask <<= (shift * 8); | |
| data <<= (shift * 8); | |
| index &= ~3; | |
| } | |
| tmp = __cpu_to_le32(data); | |
| generic_ocp_write(tp, index, byen, sizeof(tmp), &tmp, type); | |
| } | |
| static u8 ocp_read_byte(struct r8152 *tp, u16 type, u16 index) | |
| { | |
| u32 data; | |
| __le32 tmp; | |
| u8 shift = index & 3; | |
| index &= ~3; | |
| generic_ocp_read(tp, index, sizeof(tmp), &tmp, type); | |
| data = __le32_to_cpu(tmp); | |
| data >>= (shift * 8); | |
| data &= 0xff; | |
| return (u8)data; | |
| } | |
| static void ocp_write_byte(struct r8152 *tp, u16 type, u16 index, u32 data) | |
| { | |
| u32 mask = 0xff; | |
| __le32 tmp; | |
| u16 byen = BYTE_EN_BYTE; | |
| u8 shift = index & 3; | |
| data &= mask; | |
| if (index & 3) { | |
| byen <<= shift; | |
| mask <<= (shift * 8); | |
| data <<= (shift * 8); | |
| index &= ~3; | |
| } | |
| tmp = __cpu_to_le32(data); | |
| generic_ocp_write(tp, index, byen, sizeof(tmp), &tmp, type); | |
| } | |
| static u16 ocp_reg_read(struct r8152 *tp, u16 addr) | |
| { | |
| u16 ocp_base, ocp_index; | |
| ocp_base = addr & 0xf000; | |
| if (ocp_base != tp->ocp_base) { | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_OCP_GPHY_BASE, ocp_base); | |
| tp->ocp_base = ocp_base; | |
| } | |
| ocp_index = (addr & 0x0fff) | 0xb000; | |
| return ocp_read_word(tp, MCU_TYPE_PLA, ocp_index); | |
| } | |
| static void ocp_reg_write(struct r8152 *tp, u16 addr, u16 data) | |
| { | |
| u16 ocp_base, ocp_index; | |
| ocp_base = addr & 0xf000; | |
| if (ocp_base != tp->ocp_base) { | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_OCP_GPHY_BASE, ocp_base); | |
| tp->ocp_base = ocp_base; | |
| } | |
| ocp_index = (addr & 0x0fff) | 0xb000; | |
| ocp_write_word(tp, MCU_TYPE_PLA, ocp_index, data); | |
| } | |
| static inline void r8152_mdio_write(struct r8152 *tp, u32 reg_addr, u32 value) | |
| { | |
| ocp_reg_write(tp, OCP_BASE_MII + reg_addr * 2, value); | |
| } | |
| static inline int r8152_mdio_read(struct r8152 *tp, u32 reg_addr) | |
| { | |
| return ocp_reg_read(tp, OCP_BASE_MII + reg_addr * 2); | |
| } | |
| static void sram_write(struct r8152 *tp, u16 addr, u16 data) | |
| { | |
| ocp_reg_write(tp, OCP_SRAM_ADDR, addr); | |
| ocp_reg_write(tp, OCP_SRAM_DATA, data); | |
| } | |
| static int read_mii_word(struct net_device *netdev, int phy_id, int reg) | |
| { | |
| struct r8152 *tp = netdev_priv(netdev); | |
| int ret; | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags)) | |
| return -ENODEV; | |
| if (phy_id != R8152_PHY_ID) | |
| return -EINVAL; | |
| ret = r8152_mdio_read(tp, reg); | |
| return ret; | |
| } | |
| static | |
| void write_mii_word(struct net_device *netdev, int phy_id, int reg, int val) | |
| { | |
| struct r8152 *tp = netdev_priv(netdev); | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags)) | |
| return; | |
| if (phy_id != R8152_PHY_ID) | |
| return; | |
| r8152_mdio_write(tp, reg, val); | |
| } | |
| static int | |
| r8152_submit_rx(struct r8152 *tp, struct rx_agg *agg, gfp_t mem_flags); | |
| static int rtl8152_set_mac_address(struct net_device *netdev, void *p) | |
| { | |
| struct r8152 *tp = netdev_priv(netdev); | |
| struct sockaddr *addr = p; | |
| int ret = -EADDRNOTAVAIL; | |
| if (!is_valid_ether_addr(addr->sa_data)) | |
| goto out1; | |
| ret = usb_autopm_get_interface(tp->intf); | |
| if (ret < 0) | |
| goto out1; | |
| mutex_lock(&tp->control); | |
| memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len); | |
| ocp_write_byte(tp, MCU_TYPE_PLA, PLA_CRWECR, CRWECR_CONFIG); | |
| pla_ocp_write(tp, PLA_IDR, BYTE_EN_SIX_BYTES, 8, addr->sa_data); | |
| ocp_write_byte(tp, MCU_TYPE_PLA, PLA_CRWECR, CRWECR_NORAML); | |
| mutex_unlock(&tp->control); | |
| usb_autopm_put_interface(tp->intf); | |
| out1: | |
| return ret; | |
| } | |
| static int set_ethernet_addr(struct r8152 *tp) | |
| { | |
| struct net_device *dev = tp->netdev; | |
| struct sockaddr sa; | |
| int ret; | |
| if (tp->version == RTL_VER_01) | |
| ret = pla_ocp_read(tp, PLA_IDR, 8, sa.sa_data); | |
| else | |
| ret = pla_ocp_read(tp, PLA_BACKUP, 8, sa.sa_data); | |
| if (ret < 0) { | |
| netif_err(tp, probe, dev, "Get ether addr fail\n"); | |
| } else if (!is_valid_ether_addr(sa.sa_data)) { | |
| netif_err(tp, probe, dev, "Invalid ether addr %pM\n", | |
| sa.sa_data); | |
| eth_hw_addr_random(dev); | |
| ether_addr_copy(sa.sa_data, dev->dev_addr); | |
| ret = rtl8152_set_mac_address(dev, &sa); | |
| netif_info(tp, probe, dev, "Random ether addr %pM\n", | |
| sa.sa_data); | |
| } else { | |
| if (tp->version == RTL_VER_01) | |
| ether_addr_copy(dev->dev_addr, sa.sa_data); | |
| else | |
| ret = rtl8152_set_mac_address(dev, &sa); | |
| } | |
| return ret; | |
| } | |
| static void read_bulk_callback(struct urb *urb) | |
| { | |
| struct net_device *netdev; | |
| int status = urb->status; | |
| struct rx_agg *agg; | |
| struct r8152 *tp; | |
| agg = urb->context; | |
| if (!agg) | |
| return; | |
| tp = agg->context; | |
| if (!tp) | |
| return; | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags)) | |
| return; | |
| if (!test_bit(WORK_ENABLE, &tp->flags)) | |
| return; | |
| netdev = tp->netdev; | |
| /* When link down, the driver would cancel all bulks. */ | |
| /* This avoid the re-submitting bulk */ | |
| if (!netif_carrier_ok(netdev)) | |
| return; | |
| usb_mark_last_busy(tp->udev); | |
| switch (status) { | |
| case 0: | |
| if (urb->actual_length < ETH_ZLEN) | |
| break; | |
| spin_lock(&tp->rx_lock); | |
| list_add_tail(&agg->list, &tp->rx_done); | |
| spin_unlock(&tp->rx_lock); | |
| napi_schedule(&tp->napi); | |
| return; | |
| case -ESHUTDOWN: | |
| set_bit(RTL8152_UNPLUG, &tp->flags); | |
| netif_device_detach(tp->netdev); | |
| return; | |
| case -ENOENT: | |
| return; /* the urb is in unlink state */ | |
| case -ETIME: | |
| if (net_ratelimit()) | |
| netdev_warn(netdev, "maybe reset is needed?\n"); | |
| break; | |
| default: | |
| if (net_ratelimit()) | |
| netdev_warn(netdev, "Rx status %d\n", status); | |
| break; | |
| } | |
| r8152_submit_rx(tp, agg, GFP_ATOMIC); | |
| } | |
| static void write_bulk_callback(struct urb *urb) | |
| { | |
| struct net_device_stats *stats; | |
| struct net_device *netdev; | |
| struct tx_agg *agg; | |
| struct r8152 *tp; | |
| int status = urb->status; | |
| agg = urb->context; | |
| if (!agg) | |
| return; | |
| tp = agg->context; | |
| if (!tp) | |
| return; | |
| netdev = tp->netdev; | |
| stats = &netdev->stats; | |
| if (status) { | |
| if (net_ratelimit()) | |
| netdev_warn(netdev, "Tx status %d\n", status); | |
| stats->tx_errors += agg->skb_num; | |
| } else { | |
| stats->tx_packets += agg->skb_num; | |
| stats->tx_bytes += agg->skb_len; | |
| } | |
| spin_lock(&tp->tx_lock); | |
| list_add_tail(&agg->list, &tp->tx_free); | |
| spin_unlock(&tp->tx_lock); | |
| usb_autopm_put_interface_async(tp->intf); | |
| if (!netif_carrier_ok(netdev)) | |
| return; | |
| if (!test_bit(WORK_ENABLE, &tp->flags)) | |
| return; | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags)) | |
| return; | |
| if (!skb_queue_empty(&tp->tx_queue)) | |
| napi_schedule(&tp->napi); | |
| } | |
| static void intr_callback(struct urb *urb) | |
| { | |
| struct r8152 *tp; | |
| __le16 *d; | |
| int status = urb->status; | |
| int res; | |
| tp = urb->context; | |
| if (!tp) | |
| return; | |
| if (!test_bit(WORK_ENABLE, &tp->flags)) | |
| return; | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags)) | |
| return; | |
| switch (status) { | |
| case 0: /* success */ | |
| break; | |
| case -ECONNRESET: /* unlink */ | |
| case -ESHUTDOWN: | |
| netif_device_detach(tp->netdev); | |
| case -ENOENT: | |
| case -EPROTO: | |
| netif_info(tp, intr, tp->netdev, | |
| "Stop submitting intr, status %d\n", status); | |
| return; | |
| case -EOVERFLOW: | |
| netif_info(tp, intr, tp->netdev, "intr status -EOVERFLOW\n"); | |
| goto resubmit; | |
| /* -EPIPE: should clear the halt */ | |
| default: | |
| netif_info(tp, intr, tp->netdev, "intr status %d\n", status); | |
| goto resubmit; | |
| } | |
| d = urb->transfer_buffer; | |
| if (INTR_LINK & __le16_to_cpu(d[0])) { | |
| if (!netif_carrier_ok(tp->netdev)) { | |
| set_bit(RTL8152_LINK_CHG, &tp->flags); | |
| schedule_delayed_work(&tp->schedule, 0); | |
| } | |
| } else { | |
| if (netif_carrier_ok(tp->netdev)) { | |
| set_bit(RTL8152_LINK_CHG, &tp->flags); | |
| schedule_delayed_work(&tp->schedule, 0); | |
| } | |
| } | |
| resubmit: | |
| res = usb_submit_urb(urb, GFP_ATOMIC); | |
| if (res == -ENODEV) { | |
| set_bit(RTL8152_UNPLUG, &tp->flags); | |
| netif_device_detach(tp->netdev); | |
| } else if (res) { | |
| netif_err(tp, intr, tp->netdev, | |
| "can't resubmit intr, status %d\n", res); | |
| } | |
| } | |
| static inline void *rx_agg_align(void *data) | |
| { | |
| return (void *)ALIGN((uintptr_t)data, RX_ALIGN); | |
| } | |
| static inline void *tx_agg_align(void *data) | |
| { | |
| return (void *)ALIGN((uintptr_t)data, TX_ALIGN); | |
| } | |
| static void free_all_mem(struct r8152 *tp) | |
| { | |
| int i; | |
| for (i = 0; i < RTL8152_MAX_RX; i++) { | |
| usb_free_urb(tp->rx_info[i].urb); | |
| tp->rx_info[i].urb = NULL; | |
| kfree(tp->rx_info[i].buffer); | |
| tp->rx_info[i].buffer = NULL; | |
| tp->rx_info[i].head = NULL; | |
| } | |
| for (i = 0; i < RTL8152_MAX_TX; i++) { | |
| usb_free_urb(tp->tx_info[i].urb); | |
| tp->tx_info[i].urb = NULL; | |
| kfree(tp->tx_info[i].buffer); | |
| tp->tx_info[i].buffer = NULL; | |
| tp->tx_info[i].head = NULL; | |
| } | |
| usb_free_urb(tp->intr_urb); | |
| tp->intr_urb = NULL; | |
| kfree(tp->intr_buff); | |
| tp->intr_buff = NULL; | |
| } | |
| static int alloc_all_mem(struct r8152 *tp) | |
| { | |
| struct net_device *netdev = tp->netdev; | |
| struct usb_interface *intf = tp->intf; | |
| struct usb_host_interface *alt = intf->cur_altsetting; | |
| struct usb_host_endpoint *ep_intr = alt->endpoint + 2; | |
| struct urb *urb; | |
| int node, i; | |
| u8 *buf; | |
| node = netdev->dev.parent ? dev_to_node(netdev->dev.parent) : -1; | |
| spin_lock_init(&tp->rx_lock); | |
| spin_lock_init(&tp->tx_lock); | |
| INIT_LIST_HEAD(&tp->tx_free); | |
| skb_queue_head_init(&tp->tx_queue); | |
| skb_queue_head_init(&tp->rx_queue); | |
| for (i = 0; i < RTL8152_MAX_RX; i++) { | |
| buf = kmalloc_node(agg_buf_sz, GFP_KERNEL, node); | |
| if (!buf) | |
| goto err1; | |
| if (buf != rx_agg_align(buf)) { | |
| kfree(buf); | |
| buf = kmalloc_node(agg_buf_sz + RX_ALIGN, GFP_KERNEL, | |
| node); | |
| if (!buf) | |
| goto err1; | |
| } | |
| urb = usb_alloc_urb(0, GFP_KERNEL); | |
| if (!urb) { | |
| kfree(buf); | |
| goto err1; | |
| } | |
| INIT_LIST_HEAD(&tp->rx_info[i].list); | |
| tp->rx_info[i].context = tp; | |
| tp->rx_info[i].urb = urb; | |
| tp->rx_info[i].buffer = buf; | |
| tp->rx_info[i].head = rx_agg_align(buf); | |
| } | |
| for (i = 0; i < RTL8152_MAX_TX; i++) { | |
| buf = kmalloc_node(agg_buf_sz, GFP_KERNEL, node); | |
| if (!buf) | |
| goto err1; | |
| if (buf != tx_agg_align(buf)) { | |
| kfree(buf); | |
| buf = kmalloc_node(agg_buf_sz + TX_ALIGN, GFP_KERNEL, | |
| node); | |
| if (!buf) | |
| goto err1; | |
| } | |
| urb = usb_alloc_urb(0, GFP_KERNEL); | |
| if (!urb) { | |
| kfree(buf); | |
| goto err1; | |
| } | |
| INIT_LIST_HEAD(&tp->tx_info[i].list); | |
| tp->tx_info[i].context = tp; | |
| tp->tx_info[i].urb = urb; | |
| tp->tx_info[i].buffer = buf; | |
| tp->tx_info[i].head = tx_agg_align(buf); | |
| list_add_tail(&tp->tx_info[i].list, &tp->tx_free); | |
| } | |
| tp->intr_urb = usb_alloc_urb(0, GFP_KERNEL); | |
| if (!tp->intr_urb) | |
| goto err1; | |
| tp->intr_buff = kmalloc(INTBUFSIZE, GFP_KERNEL); | |
| if (!tp->intr_buff) | |
| goto err1; | |
| tp->intr_interval = (int)ep_intr->desc.bInterval; | |
| usb_fill_int_urb(tp->intr_urb, tp->udev, usb_rcvintpipe(tp->udev, 3), | |
| tp->intr_buff, INTBUFSIZE, intr_callback, | |
| tp, tp->intr_interval); | |
| return 0; | |
| err1: | |
| free_all_mem(tp); | |
| return -ENOMEM; | |
| } | |
| static struct tx_agg *r8152_get_tx_agg(struct r8152 *tp) | |
| { | |
| struct tx_agg *agg = NULL; | |
| unsigned long flags; | |
| if (list_empty(&tp->tx_free)) | |
| return NULL; | |
| spin_lock_irqsave(&tp->tx_lock, flags); | |
| if (!list_empty(&tp->tx_free)) { | |
| struct list_head *cursor; | |
| cursor = tp->tx_free.next; | |
| list_del_init(cursor); | |
| agg = list_entry(cursor, struct tx_agg, list); | |
| } | |
| spin_unlock_irqrestore(&tp->tx_lock, flags); | |
| return agg; | |
| } | |
| /* r8152_csum_workaround() | |
| * The hw limites the value the transport offset. When the offset is out of the | |
| * range, calculate the checksum by sw. | |
| */ | |
| static void r8152_csum_workaround(struct r8152 *tp, struct sk_buff *skb, | |
| struct sk_buff_head *list) | |
| { | |
| if (skb_shinfo(skb)->gso_size) { | |
| netdev_features_t features = tp->netdev->features; | |
| struct sk_buff_head seg_list; | |
| struct sk_buff *segs, *nskb; | |
| features &= ~(NETIF_F_SG | NETIF_F_IPV6_CSUM | NETIF_F_TSO6); | |
| segs = skb_gso_segment(skb, features); | |
| if (IS_ERR(segs) || !segs) | |
| goto drop; | |
| __skb_queue_head_init(&seg_list); | |
| do { | |
| nskb = segs; | |
| segs = segs->next; | |
| nskb->next = NULL; | |
| __skb_queue_tail(&seg_list, nskb); | |
| } while (segs); | |
| skb_queue_splice(&seg_list, list); | |
| dev_kfree_skb(skb); | |
| } else if (skb->ip_summed == CHECKSUM_PARTIAL) { | |
| if (skb_checksum_help(skb) < 0) | |
| goto drop; | |
| __skb_queue_head(list, skb); | |
| } else { | |
| struct net_device_stats *stats; | |
| drop: | |
| stats = &tp->netdev->stats; | |
| stats->tx_dropped++; | |
| dev_kfree_skb(skb); | |
| } | |
| } | |
| /* msdn_giant_send_check() | |
| * According to the document of microsoft, the TCP Pseudo Header excludes the | |
| * packet length for IPv6 TCP large packets. | |
| */ | |
| static int msdn_giant_send_check(struct sk_buff *skb) | |
| { | |
| const struct ipv6hdr *ipv6h; | |
| struct tcphdr *th; | |
| int ret; | |
| ret = skb_cow_head(skb, 0); | |
| if (ret) | |
| return ret; | |
| ipv6h = ipv6_hdr(skb); | |
| th = tcp_hdr(skb); | |
| th->check = 0; | |
| th->check = ~tcp_v6_check(0, &ipv6h->saddr, &ipv6h->daddr, 0); | |
| return ret; | |
| } | |
| static inline void rtl_tx_vlan_tag(struct tx_desc *desc, struct sk_buff *skb) | |
| { | |
| if (skb_vlan_tag_present(skb)) { | |
| u32 opts2; | |
| opts2 = TX_VLAN_TAG | swab16(skb_vlan_tag_get(skb)); | |
| desc->opts2 |= cpu_to_le32(opts2); | |
| } | |
| } | |
| static inline void rtl_rx_vlan_tag(struct rx_desc *desc, struct sk_buff *skb) | |
| { | |
| u32 opts2 = le32_to_cpu(desc->opts2); | |
| if (opts2 & RX_VLAN_TAG) | |
| __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), | |
| swab16(opts2 & 0xffff)); | |
| } | |
| static int r8152_tx_csum(struct r8152 *tp, struct tx_desc *desc, | |
| struct sk_buff *skb, u32 len, u32 transport_offset) | |
| { | |
| u32 mss = skb_shinfo(skb)->gso_size; | |
| u32 opts1, opts2 = 0; | |
| int ret = TX_CSUM_SUCCESS; | |
| WARN_ON_ONCE(len > TX_LEN_MAX); | |
| opts1 = len | TX_FS | TX_LS; | |
| if (mss) { | |
| if (transport_offset > GTTCPHO_MAX) { | |
| netif_warn(tp, tx_err, tp->netdev, | |
| "Invalid transport offset 0x%x for TSO\n", | |
| transport_offset); | |
| ret = TX_CSUM_TSO; | |
| goto unavailable; | |
| } | |
| switch (vlan_get_protocol(skb)) { | |
| case htons(ETH_P_IP): | |
| opts1 |= GTSENDV4; | |
| break; | |
| case htons(ETH_P_IPV6): | |
| if (msdn_giant_send_check(skb)) { | |
| ret = TX_CSUM_TSO; | |
| goto unavailable; | |
| } | |
| opts1 |= GTSENDV6; | |
| break; | |
| default: | |
| WARN_ON_ONCE(1); | |
| break; | |
| } | |
| opts1 |= transport_offset << GTTCPHO_SHIFT; | |
| opts2 |= min(mss, MSS_MAX) << MSS_SHIFT; | |
| } else if (skb->ip_summed == CHECKSUM_PARTIAL) { | |
| u8 ip_protocol; | |
| if (transport_offset > TCPHO_MAX) { | |
| netif_warn(tp, tx_err, tp->netdev, | |
| "Invalid transport offset 0x%x\n", | |
| transport_offset); | |
| ret = TX_CSUM_NONE; | |
| goto unavailable; | |
| } | |
| switch (vlan_get_protocol(skb)) { | |
| case htons(ETH_P_IP): | |
| opts2 |= IPV4_CS; | |
| ip_protocol = ip_hdr(skb)->protocol; | |
| break; | |
| case htons(ETH_P_IPV6): | |
| opts2 |= IPV6_CS; | |
| ip_protocol = ipv6_hdr(skb)->nexthdr; | |
| break; | |
| default: | |
| ip_protocol = IPPROTO_RAW; | |
| break; | |
| } | |
| if (ip_protocol == IPPROTO_TCP) | |
| opts2 |= TCP_CS; | |
| else if (ip_protocol == IPPROTO_UDP) | |
| opts2 |= UDP_CS; | |
| else | |
| WARN_ON_ONCE(1); | |
| opts2 |= transport_offset << TCPHO_SHIFT; | |
| } | |
| desc->opts2 = cpu_to_le32(opts2); | |
| desc->opts1 = cpu_to_le32(opts1); | |
| unavailable: | |
| return ret; | |
| } | |
| static int r8152_tx_agg_fill(struct r8152 *tp, struct tx_agg *agg) | |
| { | |
| struct sk_buff_head skb_head, *tx_queue = &tp->tx_queue; | |
| int remain, ret; | |
| u8 *tx_data; | |
| __skb_queue_head_init(&skb_head); | |
| spin_lock(&tx_queue->lock); | |
| skb_queue_splice_init(tx_queue, &skb_head); | |
| spin_unlock(&tx_queue->lock); | |
| tx_data = agg->head; | |
| agg->skb_num = 0; | |
| agg->skb_len = 0; | |
| remain = agg_buf_sz; | |
| while (remain >= ETH_ZLEN + sizeof(struct tx_desc)) { | |
| struct tx_desc *tx_desc; | |
| struct sk_buff *skb; | |
| unsigned int len; | |
| u32 offset; | |
| skb = __skb_dequeue(&skb_head); | |
| if (!skb) | |
| break; | |
| len = skb->len + sizeof(*tx_desc); | |
| if (len > remain) { | |
| __skb_queue_head(&skb_head, skb); | |
| break; | |
| } | |
| tx_data = tx_agg_align(tx_data); | |
| tx_desc = (struct tx_desc *)tx_data; | |
| offset = (u32)skb_transport_offset(skb); | |
| if (r8152_tx_csum(tp, tx_desc, skb, skb->len, offset)) { | |
| r8152_csum_workaround(tp, skb, &skb_head); | |
| continue; | |
| } | |
| rtl_tx_vlan_tag(tx_desc, skb); | |
| tx_data += sizeof(*tx_desc); | |
| len = skb->len; | |
| if (skb_copy_bits(skb, 0, tx_data, len) < 0) { | |
| struct net_device_stats *stats = &tp->netdev->stats; | |
| stats->tx_dropped++; | |
| dev_kfree_skb_any(skb); | |
| tx_data -= sizeof(*tx_desc); | |
| continue; | |
| } | |
| tx_data += len; | |
| agg->skb_len += len; | |
| agg->skb_num++; | |
| dev_kfree_skb_any(skb); | |
| remain = agg_buf_sz - (int)(tx_agg_align(tx_data) - agg->head); | |
| } | |
| if (!skb_queue_empty(&skb_head)) { | |
| spin_lock(&tx_queue->lock); | |
| skb_queue_splice(&skb_head, tx_queue); | |
| spin_unlock(&tx_queue->lock); | |
| } | |
| netif_tx_lock(tp->netdev); | |
| if (netif_queue_stopped(tp->netdev) && | |
| skb_queue_len(&tp->tx_queue) < tp->tx_qlen) | |
| netif_wake_queue(tp->netdev); | |
| netif_tx_unlock(tp->netdev); | |
| ret = usb_autopm_get_interface_async(tp->intf); | |
| if (ret < 0) | |
| goto out_tx_fill; | |
| usb_fill_bulk_urb(agg->urb, tp->udev, usb_sndbulkpipe(tp->udev, 2), | |
| agg->head, (int)(tx_data - (u8 *)agg->head), | |
| (usb_complete_t)write_bulk_callback, agg); | |
| ret = usb_submit_urb(agg->urb, GFP_ATOMIC); | |
| if (ret < 0) | |
| usb_autopm_put_interface_async(tp->intf); | |
| out_tx_fill: | |
| return ret; | |
| } | |
| static u8 r8152_rx_csum(struct r8152 *tp, struct rx_desc *rx_desc) | |
| { | |
| u8 checksum = CHECKSUM_NONE; | |
| u32 opts2, opts3; | |
| if (tp->version == RTL_VER_01) | |
| goto return_result; | |
| opts2 = le32_to_cpu(rx_desc->opts2); | |
| opts3 = le32_to_cpu(rx_desc->opts3); | |
| if (opts2 & RD_IPV4_CS) { | |
| if (opts3 & IPF) | |
| checksum = CHECKSUM_NONE; | |
| else if ((opts2 & RD_UDP_CS) && (opts3 & UDPF)) | |
| checksum = CHECKSUM_NONE; | |
| else if ((opts2 & RD_TCP_CS) && (opts3 & TCPF)) | |
| checksum = CHECKSUM_NONE; | |
| else | |
| checksum = CHECKSUM_UNNECESSARY; | |
| } else if (RD_IPV6_CS) { | |
| if ((opts2 & RD_UDP_CS) && !(opts3 & UDPF)) | |
| checksum = CHECKSUM_UNNECESSARY; | |
| else if ((opts2 & RD_TCP_CS) && !(opts3 & TCPF)) | |
| checksum = CHECKSUM_UNNECESSARY; | |
| } | |
| return_result: | |
| return checksum; | |
| } | |
| static int rx_bottom(struct r8152 *tp, int budget) | |
| { | |
| unsigned long flags; | |
| struct list_head *cursor, *next, rx_queue; | |
| int ret = 0, work_done = 0; | |
| if (!skb_queue_empty(&tp->rx_queue)) { | |
| while (work_done < budget) { | |
| struct sk_buff *skb = __skb_dequeue(&tp->rx_queue); | |
| struct net_device *netdev = tp->netdev; | |
| struct net_device_stats *stats = &netdev->stats; | |
| unsigned int pkt_len; | |
| if (!skb) | |
| break; | |
| pkt_len = skb->len; | |
| napi_gro_receive(&tp->napi, skb); | |
| work_done++; | |
| stats->rx_packets++; | |
| stats->rx_bytes += pkt_len; | |
| } | |
| } | |
| if (list_empty(&tp->rx_done)) | |
| goto out1; | |
| INIT_LIST_HEAD(&rx_queue); | |
| spin_lock_irqsave(&tp->rx_lock, flags); | |
| list_splice_init(&tp->rx_done, &rx_queue); | |
| spin_unlock_irqrestore(&tp->rx_lock, flags); | |
| list_for_each_safe(cursor, next, &rx_queue) { | |
| struct rx_desc *rx_desc; | |
| struct rx_agg *agg; | |
| int len_used = 0; | |
| struct urb *urb; | |
| u8 *rx_data; | |
| list_del_init(cursor); | |
| agg = list_entry(cursor, struct rx_agg, list); | |
| urb = agg->urb; | |
| if (urb->actual_length < ETH_ZLEN) | |
| goto submit; | |
| rx_desc = agg->head; | |
| rx_data = agg->head; | |
| len_used += sizeof(struct rx_desc); | |
| while (urb->actual_length > len_used) { | |
| struct net_device *netdev = tp->netdev; | |
| struct net_device_stats *stats = &netdev->stats; | |
| unsigned int pkt_len; | |
| struct sk_buff *skb; | |
| pkt_len = le32_to_cpu(rx_desc->opts1) & RX_LEN_MASK; | |
| if (pkt_len < ETH_ZLEN) | |
| break; | |
| len_used += pkt_len; | |
| if (urb->actual_length < len_used) | |
| break; | |
| pkt_len -= CRC_SIZE; | |
| rx_data += sizeof(struct rx_desc); | |
| skb = netdev_alloc_skb_ip_align(netdev, pkt_len); | |
| if (!skb) { | |
| stats->rx_dropped++; | |
| goto find_next_rx; | |
| } | |
| skb->ip_summed = r8152_rx_csum(tp, rx_desc); | |
| memcpy(skb->data, rx_data, pkt_len); | |
| skb_put(skb, pkt_len); | |
| skb->protocol = eth_type_trans(skb, netdev); | |
| rtl_rx_vlan_tag(rx_desc, skb); | |
| if (work_done < budget) { | |
| napi_gro_receive(&tp->napi, skb); | |
| work_done++; | |
| stats->rx_packets++; | |
| stats->rx_bytes += pkt_len; | |
| } else { | |
| __skb_queue_tail(&tp->rx_queue, skb); | |
| } | |
| find_next_rx: | |
| rx_data = rx_agg_align(rx_data + pkt_len + CRC_SIZE); | |
| rx_desc = (struct rx_desc *)rx_data; | |
| len_used = (int)(rx_data - (u8 *)agg->head); | |
| len_used += sizeof(struct rx_desc); | |
| } | |
| submit: | |
| if (!ret) { | |
| ret = r8152_submit_rx(tp, agg, GFP_ATOMIC); | |
| } else { | |
| urb->actual_length = 0; | |
| list_add_tail(&agg->list, next); | |
| } | |
| } | |
| if (!list_empty(&rx_queue)) { | |
| spin_lock_irqsave(&tp->rx_lock, flags); | |
| list_splice_tail(&rx_queue, &tp->rx_done); | |
| spin_unlock_irqrestore(&tp->rx_lock, flags); | |
| } | |
| out1: | |
| return work_done; | |
| } | |
| static void tx_bottom(struct r8152 *tp) | |
| { | |
| int res; | |
| do { | |
| struct tx_agg *agg; | |
| if (skb_queue_empty(&tp->tx_queue)) | |
| break; | |
| agg = r8152_get_tx_agg(tp); | |
| if (!agg) | |
| break; | |
| res = r8152_tx_agg_fill(tp, agg); | |
| if (res) { | |
| struct net_device *netdev = tp->netdev; | |
| if (res == -ENODEV) { | |
| set_bit(RTL8152_UNPLUG, &tp->flags); | |
| netif_device_detach(netdev); | |
| } else { | |
| struct net_device_stats *stats = &netdev->stats; | |
| unsigned long flags; | |
| netif_warn(tp, tx_err, netdev, | |
| "failed tx_urb %d\n", res); | |
| stats->tx_dropped += agg->skb_num; | |
| spin_lock_irqsave(&tp->tx_lock, flags); | |
| list_add_tail(&agg->list, &tp->tx_free); | |
| spin_unlock_irqrestore(&tp->tx_lock, flags); | |
| } | |
| } | |
| } while (res == 0); | |
| } | |
| static void bottom_half(struct r8152 *tp) | |
| { | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags)) | |
| return; | |
| if (!test_bit(WORK_ENABLE, &tp->flags)) | |
| return; | |
| /* When link down, the driver would cancel all bulks. */ | |
| /* This avoid the re-submitting bulk */ | |
| if (!netif_carrier_ok(tp->netdev)) | |
| return; | |
| clear_bit(SCHEDULE_NAPI, &tp->flags); | |
| tx_bottom(tp); | |
| } | |
| static int r8152_poll(struct napi_struct *napi, int budget) | |
| { | |
| struct r8152 *tp = container_of(napi, struct r8152, napi); | |
| int work_done; | |
| work_done = rx_bottom(tp, budget); | |
| bottom_half(tp); | |
| if (work_done < budget) { | |
| napi_complete(napi); | |
| if (!list_empty(&tp->rx_done)) | |
| napi_schedule(napi); | |
| } | |
| return work_done; | |
| } | |
| static | |
| int r8152_submit_rx(struct r8152 *tp, struct rx_agg *agg, gfp_t mem_flags) | |
| { | |
| int ret; | |
| /* The rx would be stopped, so skip submitting */ | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags) || | |
| !test_bit(WORK_ENABLE, &tp->flags) || !netif_carrier_ok(tp->netdev)) | |
| return 0; | |
| usb_fill_bulk_urb(agg->urb, tp->udev, usb_rcvbulkpipe(tp->udev, 1), | |
| agg->head, agg_buf_sz, | |
| (usb_complete_t)read_bulk_callback, agg); | |
| ret = usb_submit_urb(agg->urb, mem_flags); | |
| if (ret == -ENODEV) { | |
| set_bit(RTL8152_UNPLUG, &tp->flags); | |
| netif_device_detach(tp->netdev); | |
| } else if (ret) { | |
| struct urb *urb = agg->urb; | |
| unsigned long flags; | |
| urb->actual_length = 0; | |
| spin_lock_irqsave(&tp->rx_lock, flags); | |
| list_add_tail(&agg->list, &tp->rx_done); | |
| spin_unlock_irqrestore(&tp->rx_lock, flags); | |
| netif_err(tp, rx_err, tp->netdev, | |
| "Couldn't submit rx[%p], ret = %d\n", agg, ret); | |
| napi_schedule(&tp->napi); | |
| } | |
| return ret; | |
| } | |
| static void rtl_drop_queued_tx(struct r8152 *tp) | |
| { | |
| struct net_device_stats *stats = &tp->netdev->stats; | |
| struct sk_buff_head skb_head, *tx_queue = &tp->tx_queue; | |
| struct sk_buff *skb; | |
| if (skb_queue_empty(tx_queue)) | |
| return; | |
| __skb_queue_head_init(&skb_head); | |
| spin_lock_bh(&tx_queue->lock); | |
| skb_queue_splice_init(tx_queue, &skb_head); | |
| spin_unlock_bh(&tx_queue->lock); | |
| while ((skb = __skb_dequeue(&skb_head))) { | |
| dev_kfree_skb(skb); | |
| stats->tx_dropped++; | |
| } | |
| } | |
| static void rtl8152_tx_timeout(struct net_device *netdev) | |
| { | |
| struct r8152 *tp = netdev_priv(netdev); | |
| netif_warn(tp, tx_err, netdev, "Tx timeout\n"); | |
| usb_queue_reset_device(tp->intf); | |
| } | |
| static void rtl8152_set_rx_mode(struct net_device *netdev) | |
| { | |
| struct r8152 *tp = netdev_priv(netdev); | |
| if (netif_carrier_ok(netdev)) { | |
| set_bit(RTL8152_SET_RX_MODE, &tp->flags); | |
| schedule_delayed_work(&tp->schedule, 0); | |
| } | |
| } | |
| static void _rtl8152_set_rx_mode(struct net_device *netdev) | |
| { | |
| struct r8152 *tp = netdev_priv(netdev); | |
| u32 mc_filter[2]; /* Multicast hash filter */ | |
| __le32 tmp[2]; | |
| u32 ocp_data; | |
| clear_bit(RTL8152_SET_RX_MODE, &tp->flags); | |
| netif_stop_queue(netdev); | |
| ocp_data = ocp_read_dword(tp, MCU_TYPE_PLA, PLA_RCR); | |
| ocp_data &= ~RCR_ACPT_ALL; | |
| ocp_data |= RCR_AB | RCR_APM; | |
| if (netdev->flags & IFF_PROMISC) { | |
| /* Unconditionally log net taps. */ | |
| netif_notice(tp, link, netdev, "Promiscuous mode enabled\n"); | |
| ocp_data |= RCR_AM | RCR_AAP; | |
| mc_filter[1] = 0xffffffff; | |
| mc_filter[0] = 0xffffffff; | |
| } else if ((netdev_mc_count(netdev) > multicast_filter_limit) || | |
| (netdev->flags & IFF_ALLMULTI)) { | |
| /* Too many to filter perfectly -- accept all multicasts. */ | |
| ocp_data |= RCR_AM; | |
| mc_filter[1] = 0xffffffff; | |
| mc_filter[0] = 0xffffffff; | |
| } else { | |
| struct netdev_hw_addr *ha; | |
| mc_filter[1] = 0; | |
| mc_filter[0] = 0; | |
| netdev_for_each_mc_addr(ha, netdev) { | |
| int bit_nr = ether_crc(ETH_ALEN, ha->addr) >> 26; | |
| mc_filter[bit_nr >> 5] |= 1 << (bit_nr & 31); | |
| ocp_data |= RCR_AM; | |
| } | |
| } | |
| tmp[0] = __cpu_to_le32(swab32(mc_filter[1])); | |
| tmp[1] = __cpu_to_le32(swab32(mc_filter[0])); | |
| pla_ocp_write(tp, PLA_MAR, BYTE_EN_DWORD, sizeof(tmp), tmp); | |
| ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RCR, ocp_data); | |
| netif_wake_queue(netdev); | |
| } | |
| static netdev_features_t | |
| rtl8152_features_check(struct sk_buff *skb, struct net_device *dev, | |
| netdev_features_t features) | |
| { | |
| u32 mss = skb_shinfo(skb)->gso_size; | |
| int max_offset = mss ? GTTCPHO_MAX : TCPHO_MAX; | |
| int offset = skb_transport_offset(skb); | |
| if ((mss || skb->ip_summed == CHECKSUM_PARTIAL) && offset > max_offset) | |
| features &= ~(NETIF_F_ALL_CSUM | NETIF_F_GSO_MASK); | |
| else if ((skb->len + sizeof(struct tx_desc)) > agg_buf_sz) | |
| features &= ~NETIF_F_GSO_MASK; | |
| return features; | |
| } | |
| static netdev_tx_t rtl8152_start_xmit(struct sk_buff *skb, | |
| struct net_device *netdev) | |
| { | |
| struct r8152 *tp = netdev_priv(netdev); | |
| skb_tx_timestamp(skb); | |
| skb_queue_tail(&tp->tx_queue, skb); | |
| if (!list_empty(&tp->tx_free)) { | |
| if (test_bit(SELECTIVE_SUSPEND, &tp->flags)) { | |
| set_bit(SCHEDULE_NAPI, &tp->flags); | |
| schedule_delayed_work(&tp->schedule, 0); | |
| } else { | |
| usb_mark_last_busy(tp->udev); | |
| napi_schedule(&tp->napi); | |
| } | |
| } else if (skb_queue_len(&tp->tx_queue) > tp->tx_qlen) { | |
| netif_stop_queue(netdev); | |
| } | |
| return NETDEV_TX_OK; | |
| } | |
| static void r8152b_reset_packet_filter(struct r8152 *tp) | |
| { | |
| u32 ocp_data; | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_FMC); | |
| ocp_data &= ~FMC_FCR_MCU_EN; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_FMC, ocp_data); | |
| ocp_data |= FMC_FCR_MCU_EN; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_FMC, ocp_data); | |
| } | |
| static void rtl8152_nic_reset(struct r8152 *tp) | |
| { | |
| int i; | |
| ocp_write_byte(tp, MCU_TYPE_PLA, PLA_CR, CR_RST); | |
| for (i = 0; i < 1000; i++) { | |
| if (!(ocp_read_byte(tp, MCU_TYPE_PLA, PLA_CR) & CR_RST)) | |
| break; | |
| usleep_range(100, 400); | |
| } | |
| } | |
| static void set_tx_qlen(struct r8152 *tp) | |
| { | |
| struct net_device *netdev = tp->netdev; | |
| tp->tx_qlen = agg_buf_sz / (netdev->mtu + VLAN_ETH_HLEN + VLAN_HLEN + | |
| sizeof(struct tx_desc)); | |
| } | |
| static inline u8 rtl8152_get_speed(struct r8152 *tp) | |
| { | |
| return ocp_read_byte(tp, MCU_TYPE_PLA, PLA_PHYSTATUS); | |
| } | |
| static void rtl_set_eee_plus(struct r8152 *tp) | |
| { | |
| u32 ocp_data; | |
| u8 speed; | |
| speed = rtl8152_get_speed(tp); | |
| if (speed & _10bps) { | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_EEEP_CR); | |
| ocp_data |= EEEP_CR_EEEP_TX; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_EEEP_CR, ocp_data); | |
| } else { | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_EEEP_CR); | |
| ocp_data &= ~EEEP_CR_EEEP_TX; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_EEEP_CR, ocp_data); | |
| } | |
| } | |
| static void rxdy_gated_en(struct r8152 *tp, bool enable) | |
| { | |
| u32 ocp_data; | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_MISC_1); | |
| if (enable) | |
| ocp_data |= RXDY_GATED_EN; | |
| else | |
| ocp_data &= ~RXDY_GATED_EN; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_MISC_1, ocp_data); | |
| } | |
| static int rtl_start_rx(struct r8152 *tp) | |
| { | |
| int i, ret = 0; | |
| INIT_LIST_HEAD(&tp->rx_done); | |
| for (i = 0; i < RTL8152_MAX_RX; i++) { | |
| INIT_LIST_HEAD(&tp->rx_info[i].list); | |
| ret = r8152_submit_rx(tp, &tp->rx_info[i], GFP_KERNEL); | |
| if (ret) | |
| break; | |
| } | |
| if (ret && ++i < RTL8152_MAX_RX) { | |
| struct list_head rx_queue; | |
| unsigned long flags; | |
| INIT_LIST_HEAD(&rx_queue); | |
| do { | |
| struct rx_agg *agg = &tp->rx_info[i++]; | |
| struct urb *urb = agg->urb; | |
| urb->actual_length = 0; | |
| list_add_tail(&agg->list, &rx_queue); | |
| } while (i < RTL8152_MAX_RX); | |
| spin_lock_irqsave(&tp->rx_lock, flags); | |
| list_splice_tail(&rx_queue, &tp->rx_done); | |
| spin_unlock_irqrestore(&tp->rx_lock, flags); | |
| } | |
| return ret; | |
| } | |
| static int rtl_stop_rx(struct r8152 *tp) | |
| { | |
| int i; | |
| for (i = 0; i < RTL8152_MAX_RX; i++) | |
| usb_kill_urb(tp->rx_info[i].urb); | |
| while (!skb_queue_empty(&tp->rx_queue)) | |
| dev_kfree_skb(__skb_dequeue(&tp->rx_queue)); | |
| return 0; | |
| } | |
| static int rtl_enable(struct r8152 *tp) | |
| { | |
| u32 ocp_data; | |
| r8152b_reset_packet_filter(tp); | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_CR); | |
| ocp_data |= CR_RE | CR_TE; | |
| ocp_write_byte(tp, MCU_TYPE_PLA, PLA_CR, ocp_data); | |
| rxdy_gated_en(tp, false); | |
| return 0; | |
| } | |
| static int rtl8152_enable(struct r8152 *tp) | |
| { | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags)) | |
| return -ENODEV; | |
| set_tx_qlen(tp); | |
| rtl_set_eee_plus(tp); | |
| return rtl_enable(tp); | |
| } | |
| static void r8153_set_rx_early_timeout(struct r8152 *tp) | |
| { | |
| u32 ocp_data = tp->coalesce / 8; | |
| ocp_write_word(tp, MCU_TYPE_USB, USB_RX_EARLY_TIMEOUT, ocp_data); | |
| } | |
| static void r8153_set_rx_early_size(struct r8152 *tp) | |
| { | |
| u32 mtu = tp->netdev->mtu; | |
| u32 ocp_data = (agg_buf_sz - mtu - VLAN_ETH_HLEN - VLAN_HLEN) / 4; | |
| ocp_write_word(tp, MCU_TYPE_USB, USB_RX_EARLY_SIZE, ocp_data); | |
| } | |
| static int rtl8153_enable(struct r8152 *tp) | |
| { | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags)) | |
| return -ENODEV; | |
| usb_disable_lpm(tp->udev); | |
| set_tx_qlen(tp); | |
| rtl_set_eee_plus(tp); | |
| r8153_set_rx_early_timeout(tp); | |
| r8153_set_rx_early_size(tp); | |
| return rtl_enable(tp); | |
| } | |
| static void rtl_disable(struct r8152 *tp) | |
| { | |
| u32 ocp_data; | |
| int i; | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags)) { | |
| rtl_drop_queued_tx(tp); | |
| return; | |
| } | |
| ocp_data = ocp_read_dword(tp, MCU_TYPE_PLA, PLA_RCR); | |
| ocp_data &= ~RCR_ACPT_ALL; | |
| ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RCR, ocp_data); | |
| rtl_drop_queued_tx(tp); | |
| for (i = 0; i < RTL8152_MAX_TX; i++) | |
| usb_kill_urb(tp->tx_info[i].urb); | |
| rxdy_gated_en(tp, true); | |
| for (i = 0; i < 1000; i++) { | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL); | |
| if ((ocp_data & FIFO_EMPTY) == FIFO_EMPTY) | |
| break; | |
| usleep_range(1000, 2000); | |
| } | |
| for (i = 0; i < 1000; i++) { | |
| if (ocp_read_word(tp, MCU_TYPE_PLA, PLA_TCR0) & TCR0_TX_EMPTY) | |
| break; | |
| usleep_range(1000, 2000); | |
| } | |
| rtl_stop_rx(tp); | |
| rtl8152_nic_reset(tp); | |
| } | |
| static void r8152_power_cut_en(struct r8152 *tp, bool enable) | |
| { | |
| u32 ocp_data; | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_USB, USB_UPS_CTRL); | |
| if (enable) | |
| ocp_data |= POWER_CUT; | |
| else | |
| ocp_data &= ~POWER_CUT; | |
| ocp_write_word(tp, MCU_TYPE_USB, USB_UPS_CTRL, ocp_data); | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_USB, USB_PM_CTRL_STATUS); | |
| ocp_data &= ~RESUME_INDICATE; | |
| ocp_write_word(tp, MCU_TYPE_USB, USB_PM_CTRL_STATUS, ocp_data); | |
| } | |
| static void rtl_rx_vlan_en(struct r8152 *tp, bool enable) | |
| { | |
| u32 ocp_data; | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_CPCR); | |
| if (enable) | |
| ocp_data |= CPCR_RX_VLAN; | |
| else | |
| ocp_data &= ~CPCR_RX_VLAN; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_CPCR, ocp_data); | |
| } | |
| static int rtl8152_set_features(struct net_device *dev, | |
| netdev_features_t features) | |
| { | |
| netdev_features_t changed = features ^ dev->features; | |
| struct r8152 *tp = netdev_priv(dev); | |
| int ret; | |
| ret = usb_autopm_get_interface(tp->intf); | |
| if (ret < 0) | |
| goto out; | |
| mutex_lock(&tp->control); | |
| if (changed & NETIF_F_HW_VLAN_CTAG_RX) { | |
| if (features & NETIF_F_HW_VLAN_CTAG_RX) | |
| rtl_rx_vlan_en(tp, true); | |
| else | |
| rtl_rx_vlan_en(tp, false); | |
| } | |
| mutex_unlock(&tp->control); | |
| usb_autopm_put_interface(tp->intf); | |
| out: | |
| return ret; | |
| } | |
| #define WAKE_ANY (WAKE_PHY | WAKE_MAGIC | WAKE_UCAST | WAKE_BCAST | WAKE_MCAST) | |
| static u32 __rtl_get_wol(struct r8152 *tp) | |
| { | |
| u32 ocp_data; | |
| u32 wolopts = 0; | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_CONFIG5); | |
| if (!(ocp_data & LAN_WAKE_EN)) | |
| return 0; | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_CONFIG34); | |
| if (ocp_data & LINK_ON_WAKE_EN) | |
| wolopts |= WAKE_PHY; | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_CONFIG5); | |
| if (ocp_data & UWF_EN) | |
| wolopts |= WAKE_UCAST; | |
| if (ocp_data & BWF_EN) | |
| wolopts |= WAKE_BCAST; | |
| if (ocp_data & MWF_EN) | |
| wolopts |= WAKE_MCAST; | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_CFG_WOL); | |
| if (ocp_data & MAGIC_EN) | |
| wolopts |= WAKE_MAGIC; | |
| return wolopts; | |
| } | |
| static void __rtl_set_wol(struct r8152 *tp, u32 wolopts) | |
| { | |
| u32 ocp_data; | |
| ocp_write_byte(tp, MCU_TYPE_PLA, PLA_CRWECR, CRWECR_CONFIG); | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_CONFIG34); | |
| ocp_data &= ~LINK_ON_WAKE_EN; | |
| if (wolopts & WAKE_PHY) | |
| ocp_data |= LINK_ON_WAKE_EN; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_CONFIG34, ocp_data); | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_CONFIG5); | |
| ocp_data &= ~(UWF_EN | BWF_EN | MWF_EN | LAN_WAKE_EN); | |
| if (wolopts & WAKE_UCAST) | |
| ocp_data |= UWF_EN; | |
| if (wolopts & WAKE_BCAST) | |
| ocp_data |= BWF_EN; | |
| if (wolopts & WAKE_MCAST) | |
| ocp_data |= MWF_EN; | |
| if (wolopts & WAKE_ANY) | |
| ocp_data |= LAN_WAKE_EN; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_CONFIG5, ocp_data); | |
| ocp_write_byte(tp, MCU_TYPE_PLA, PLA_CRWECR, CRWECR_NORAML); | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_CFG_WOL); | |
| ocp_data &= ~MAGIC_EN; | |
| if (wolopts & WAKE_MAGIC) | |
| ocp_data |= MAGIC_EN; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_CFG_WOL, ocp_data); | |
| if (wolopts & WAKE_ANY) | |
| device_set_wakeup_enable(&tp->udev->dev, true); | |
| else | |
| device_set_wakeup_enable(&tp->udev->dev, false); | |
| } | |
| static void r8153_u1u2en(struct r8152 *tp, bool enable) | |
| { | |
| u8 u1u2[8]; | |
| if (enable) | |
| memset(u1u2, 0xff, sizeof(u1u2)); | |
| else | |
| memset(u1u2, 0x00, sizeof(u1u2)); | |
| usb_ocp_write(tp, USB_TOLERANCE, BYTE_EN_SIX_BYTES, sizeof(u1u2), u1u2); | |
| } | |
| static void r8153_u2p3en(struct r8152 *tp, bool enable) | |
| { | |
| u32 ocp_data; | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_USB, USB_U2P3_CTRL); | |
| if (enable && tp->version != RTL_VER_03 && tp->version != RTL_VER_04) | |
| ocp_data |= U2P3_ENABLE; | |
| else | |
| ocp_data &= ~U2P3_ENABLE; | |
| ocp_write_word(tp, MCU_TYPE_USB, USB_U2P3_CTRL, ocp_data); | |
| } | |
| static void r8153_power_cut_en(struct r8152 *tp, bool enable) | |
| { | |
| u32 ocp_data; | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_USB, USB_POWER_CUT); | |
| if (enable) | |
| ocp_data |= PWR_EN | PHASE2_EN; | |
| else | |
| ocp_data &= ~(PWR_EN | PHASE2_EN); | |
| ocp_write_word(tp, MCU_TYPE_USB, USB_POWER_CUT, ocp_data); | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_USB, USB_MISC_0); | |
| ocp_data &= ~PCUT_STATUS; | |
| ocp_write_word(tp, MCU_TYPE_USB, USB_MISC_0, ocp_data); | |
| } | |
| static bool rtl_can_wakeup(struct r8152 *tp) | |
| { | |
| struct usb_device *udev = tp->udev; | |
| return (udev->actconfig->desc.bmAttributes & USB_CONFIG_ATT_WAKEUP); | |
| } | |
| static void rtl_runtime_suspend_enable(struct r8152 *tp, bool enable) | |
| { | |
| if (enable) { | |
| u32 ocp_data; | |
| r8153_u1u2en(tp, false); | |
| r8153_u2p3en(tp, false); | |
| __rtl_set_wol(tp, WAKE_ANY); | |
| ocp_write_byte(tp, MCU_TYPE_PLA, PLA_CRWECR, CRWECR_CONFIG); | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_CONFIG34); | |
| ocp_data |= LINK_OFF_WAKE_EN; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_CONFIG34, ocp_data); | |
| ocp_write_byte(tp, MCU_TYPE_PLA, PLA_CRWECR, CRWECR_NORAML); | |
| } else { | |
| __rtl_set_wol(tp, tp->saved_wolopts); | |
| r8153_u2p3en(tp, true); | |
| r8153_u1u2en(tp, true); | |
| } | |
| } | |
| static void rtl_phy_reset(struct r8152 *tp) | |
| { | |
| u16 data; | |
| int i; | |
| clear_bit(PHY_RESET, &tp->flags); | |
| data = r8152_mdio_read(tp, MII_BMCR); | |
| /* don't reset again before the previous one complete */ | |
| if (data & BMCR_RESET) | |
| return; | |
| data |= BMCR_RESET; | |
| r8152_mdio_write(tp, MII_BMCR, data); | |
| for (i = 0; i < 50; i++) { | |
| msleep(20); | |
| if ((r8152_mdio_read(tp, MII_BMCR) & BMCR_RESET) == 0) | |
| break; | |
| } | |
| } | |
| static void r8153_teredo_off(struct r8152 *tp) | |
| { | |
| u32 ocp_data; | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_TEREDO_CFG); | |
| ocp_data &= ~(TEREDO_SEL | TEREDO_RS_EVENT_MASK | OOB_TEREDO_EN); | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_TEREDO_CFG, ocp_data); | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_WDT6_CTRL, WDT6_SET_MODE); | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_REALWOW_TIMER, 0); | |
| ocp_write_dword(tp, MCU_TYPE_PLA, PLA_TEREDO_TIMER, 0); | |
| } | |
| static void r8152b_disable_aldps(struct r8152 *tp) | |
| { | |
| ocp_reg_write(tp, OCP_ALDPS_CONFIG, ENPDNPS | LINKENA | DIS_SDSAVE); | |
| msleep(20); | |
| } | |
| static inline void r8152b_enable_aldps(struct r8152 *tp) | |
| { | |
| ocp_reg_write(tp, OCP_ALDPS_CONFIG, ENPWRSAVE | ENPDNPS | | |
| LINKENA | DIS_SDSAVE); | |
| } | |
| static void rtl8152_disable(struct r8152 *tp) | |
| { | |
| r8152b_disable_aldps(tp); | |
| rtl_disable(tp); | |
| r8152b_enable_aldps(tp); | |
| } | |
| static void r8152b_hw_phy_cfg(struct r8152 *tp) | |
| { | |
| u16 data; | |
| data = r8152_mdio_read(tp, MII_BMCR); | |
| if (data & BMCR_PDOWN) { | |
| data &= ~BMCR_PDOWN; | |
| r8152_mdio_write(tp, MII_BMCR, data); | |
| } | |
| set_bit(PHY_RESET, &tp->flags); | |
| } | |
| static void r8152b_exit_oob(struct r8152 *tp) | |
| { | |
| u32 ocp_data; | |
| int i; | |
| ocp_data = ocp_read_dword(tp, MCU_TYPE_PLA, PLA_RCR); | |
| ocp_data &= ~RCR_ACPT_ALL; | |
| ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RCR, ocp_data); | |
| rxdy_gated_en(tp, true); | |
| r8153_teredo_off(tp); | |
| r8152b_hw_phy_cfg(tp); | |
| ocp_write_byte(tp, MCU_TYPE_PLA, PLA_CRWECR, CRWECR_NORAML); | |
| ocp_write_byte(tp, MCU_TYPE_PLA, PLA_CR, 0x00); | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL); | |
| ocp_data &= ~NOW_IS_OOB; | |
| ocp_write_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL, ocp_data); | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7); | |
| ocp_data &= ~MCU_BORW_EN; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7, ocp_data); | |
| for (i = 0; i < 1000; i++) { | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL); | |
| if (ocp_data & LINK_LIST_READY) | |
| break; | |
| usleep_range(1000, 2000); | |
| } | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7); | |
| ocp_data |= RE_INIT_LL; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7, ocp_data); | |
| for (i = 0; i < 1000; i++) { | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL); | |
| if (ocp_data & LINK_LIST_READY) | |
| break; | |
| usleep_range(1000, 2000); | |
| } | |
| rtl8152_nic_reset(tp); | |
| /* rx share fifo credit full threshold */ | |
| ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RXFIFO_CTRL0, RXFIFO_THR1_NORMAL); | |
| if (tp->udev->speed == USB_SPEED_FULL || | |
| tp->udev->speed == USB_SPEED_LOW) { | |
| /* rx share fifo credit near full threshold */ | |
| ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RXFIFO_CTRL1, | |
| RXFIFO_THR2_FULL); | |
| ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RXFIFO_CTRL2, | |
| RXFIFO_THR3_FULL); | |
| } else { | |
| /* rx share fifo credit near full threshold */ | |
| ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RXFIFO_CTRL1, | |
| RXFIFO_THR2_HIGH); | |
| ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RXFIFO_CTRL2, | |
| RXFIFO_THR3_HIGH); | |
| } | |
| /* TX share fifo free credit full threshold */ | |
| ocp_write_dword(tp, MCU_TYPE_PLA, PLA_TXFIFO_CTRL, TXFIFO_THR_NORMAL); | |
| ocp_write_byte(tp, MCU_TYPE_USB, USB_TX_AGG, TX_AGG_MAX_THRESHOLD); | |
| ocp_write_dword(tp, MCU_TYPE_USB, USB_RX_BUF_TH, RX_THR_HIGH); | |
| ocp_write_dword(tp, MCU_TYPE_USB, USB_TX_DMA, | |
| TEST_MODE_DISABLE | TX_SIZE_ADJUST1); | |
| rtl_rx_vlan_en(tp, tp->netdev->features & NETIF_F_HW_VLAN_CTAG_RX); | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_RMS, RTL8152_RMS); | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_TCR0); | |
| ocp_data |= TCR0_AUTO_FIFO; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_TCR0, ocp_data); | |
| } | |
| static void r8152b_enter_oob(struct r8152 *tp) | |
| { | |
| u32 ocp_data; | |
| int i; | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL); | |
| ocp_data &= ~NOW_IS_OOB; | |
| ocp_write_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL, ocp_data); | |
| ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RXFIFO_CTRL0, RXFIFO_THR1_OOB); | |
| ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RXFIFO_CTRL1, RXFIFO_THR2_OOB); | |
| ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RXFIFO_CTRL2, RXFIFO_THR3_OOB); | |
| rtl_disable(tp); | |
| for (i = 0; i < 1000; i++) { | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL); | |
| if (ocp_data & LINK_LIST_READY) | |
| break; | |
| usleep_range(1000, 2000); | |
| } | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7); | |
| ocp_data |= RE_INIT_LL; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7, ocp_data); | |
| for (i = 0; i < 1000; i++) { | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL); | |
| if (ocp_data & LINK_LIST_READY) | |
| break; | |
| usleep_range(1000, 2000); | |
| } | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_RMS, RTL8152_RMS); | |
| rtl_rx_vlan_en(tp, true); | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PAL_BDC_CR); | |
| ocp_data |= ALDPS_PROXY_MODE; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PAL_BDC_CR, ocp_data); | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL); | |
| ocp_data |= NOW_IS_OOB | DIS_MCU_CLROOB; | |
| ocp_write_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL, ocp_data); | |
| rxdy_gated_en(tp, false); | |
| ocp_data = ocp_read_dword(tp, MCU_TYPE_PLA, PLA_RCR); | |
| ocp_data |= RCR_APM | RCR_AM | RCR_AB; | |
| ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RCR, ocp_data); | |
| } | |
| static void r8153_hw_phy_cfg(struct r8152 *tp) | |
| { | |
| u32 ocp_data; | |
| u16 data; | |
| if (tp->version == RTL_VER_03 || tp->version == RTL_VER_04 || | |
| tp->version == RTL_VER_05) | |
| ocp_reg_write(tp, OCP_ADC_CFG, CKADSEL_L | ADC_EN | EN_EMI_L); | |
| data = r8152_mdio_read(tp, MII_BMCR); | |
| if (data & BMCR_PDOWN) { | |
| data &= ~BMCR_PDOWN; | |
| r8152_mdio_write(tp, MII_BMCR, data); | |
| } | |
| if (tp->version == RTL_VER_03) { | |
| data = ocp_reg_read(tp, OCP_EEE_CFG); | |
| data &= ~CTAP_SHORT_EN; | |
| ocp_reg_write(tp, OCP_EEE_CFG, data); | |
| } | |
| data = ocp_reg_read(tp, OCP_POWER_CFG); | |
| data |= EEE_CLKDIV_EN; | |
| ocp_reg_write(tp, OCP_POWER_CFG, data); | |
| data = ocp_reg_read(tp, OCP_DOWN_SPEED); | |
| data |= EN_10M_BGOFF; | |
| ocp_reg_write(tp, OCP_DOWN_SPEED, data); | |
| data = ocp_reg_read(tp, OCP_POWER_CFG); | |
| data |= EN_10M_PLLOFF; | |
| ocp_reg_write(tp, OCP_POWER_CFG, data); | |
| sram_write(tp, SRAM_IMPEDANCE, 0x0b13); | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_PHY_PWR); | |
| ocp_data |= PFM_PWM_SWITCH; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_PHY_PWR, ocp_data); | |
| /* Enable LPF corner auto tune */ | |
| sram_write(tp, SRAM_LPF_CFG, 0xf70f); | |
| /* Adjust 10M Amplitude */ | |
| sram_write(tp, SRAM_10M_AMP1, 0x00af); | |
| sram_write(tp, SRAM_10M_AMP2, 0x0208); | |
| set_bit(PHY_RESET, &tp->flags); | |
| } | |
| static void r8153_first_init(struct r8152 *tp) | |
| { | |
| u32 ocp_data; | |
| int i; | |
| rxdy_gated_en(tp, true); | |
| r8153_teredo_off(tp); | |
| ocp_data = ocp_read_dword(tp, MCU_TYPE_PLA, PLA_RCR); | |
| ocp_data &= ~RCR_ACPT_ALL; | |
| ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RCR, ocp_data); | |
| r8153_hw_phy_cfg(tp); | |
| rtl8152_nic_reset(tp); | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL); | |
| ocp_data &= ~NOW_IS_OOB; | |
| ocp_write_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL, ocp_data); | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7); | |
| ocp_data &= ~MCU_BORW_EN; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7, ocp_data); | |
| for (i = 0; i < 1000; i++) { | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL); | |
| if (ocp_data & LINK_LIST_READY) | |
| break; | |
| usleep_range(1000, 2000); | |
| } | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7); | |
| ocp_data |= RE_INIT_LL; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7, ocp_data); | |
| for (i = 0; i < 1000; i++) { | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL); | |
| if (ocp_data & LINK_LIST_READY) | |
| break; | |
| usleep_range(1000, 2000); | |
| } | |
| rtl_rx_vlan_en(tp, tp->netdev->features & NETIF_F_HW_VLAN_CTAG_RX); | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_RMS, RTL8153_RMS); | |
| ocp_write_byte(tp, MCU_TYPE_PLA, PLA_MTPS, MTPS_JUMBO); | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_TCR0); | |
| ocp_data |= TCR0_AUTO_FIFO; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_TCR0, ocp_data); | |
| rtl8152_nic_reset(tp); | |
| /* rx share fifo credit full threshold */ | |
| ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RXFIFO_CTRL0, RXFIFO_THR1_NORMAL); | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_RXFIFO_CTRL1, RXFIFO_THR2_NORMAL); | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_RXFIFO_CTRL2, RXFIFO_THR3_NORMAL); | |
| /* TX share fifo free credit full threshold */ | |
| ocp_write_dword(tp, MCU_TYPE_PLA, PLA_TXFIFO_CTRL, TXFIFO_THR_NORMAL2); | |
| /* rx aggregation */ | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_USB, USB_USB_CTRL); | |
| ocp_data &= ~(RX_AGG_DISABLE | RX_ZERO_EN); | |
| ocp_write_word(tp, MCU_TYPE_USB, USB_USB_CTRL, ocp_data); | |
| } | |
| static void r8153_enter_oob(struct r8152 *tp) | |
| { | |
| u32 ocp_data; | |
| int i; | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL); | |
| ocp_data &= ~NOW_IS_OOB; | |
| ocp_write_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL, ocp_data); | |
| rtl_disable(tp); | |
| for (i = 0; i < 1000; i++) { | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL); | |
| if (ocp_data & LINK_LIST_READY) | |
| break; | |
| usleep_range(1000, 2000); | |
| } | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7); | |
| ocp_data |= RE_INIT_LL; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7, ocp_data); | |
| for (i = 0; i < 1000; i++) { | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL); | |
| if (ocp_data & LINK_LIST_READY) | |
| break; | |
| usleep_range(1000, 2000); | |
| } | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_RMS, RTL8153_RMS); | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_TEREDO_CFG); | |
| ocp_data &= ~TEREDO_WAKE_MASK; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_TEREDO_CFG, ocp_data); | |
| rtl_rx_vlan_en(tp, true); | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PAL_BDC_CR); | |
| ocp_data |= ALDPS_PROXY_MODE; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PAL_BDC_CR, ocp_data); | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL); | |
| ocp_data |= NOW_IS_OOB | DIS_MCU_CLROOB; | |
| ocp_write_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL, ocp_data); | |
| rxdy_gated_en(tp, false); | |
| ocp_data = ocp_read_dword(tp, MCU_TYPE_PLA, PLA_RCR); | |
| ocp_data |= RCR_APM | RCR_AM | RCR_AB; | |
| ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RCR, ocp_data); | |
| } | |
| static void r8153_disable_aldps(struct r8152 *tp) | |
| { | |
| u16 data; | |
| data = ocp_reg_read(tp, OCP_POWER_CFG); | |
| data &= ~EN_ALDPS; | |
| ocp_reg_write(tp, OCP_POWER_CFG, data); | |
| msleep(20); | |
| } | |
| static void r8153_enable_aldps(struct r8152 *tp) | |
| { | |
| u16 data; | |
| data = ocp_reg_read(tp, OCP_POWER_CFG); | |
| data |= EN_ALDPS; | |
| ocp_reg_write(tp, OCP_POWER_CFG, data); | |
| } | |
| static void rtl8153_disable(struct r8152 *tp) | |
| { | |
| r8153_disable_aldps(tp); | |
| rtl_disable(tp); | |
| r8153_enable_aldps(tp); | |
| usb_enable_lpm(tp->udev); | |
| } | |
| static int rtl8152_set_speed(struct r8152 *tp, u8 autoneg, u16 speed, u8 duplex) | |
| { | |
| u16 bmcr, anar, gbcr; | |
| int ret = 0; | |
| cancel_delayed_work_sync(&tp->schedule); | |
| anar = r8152_mdio_read(tp, MII_ADVERTISE); | |
| anar &= ~(ADVERTISE_10HALF | ADVERTISE_10FULL | | |
| ADVERTISE_100HALF | ADVERTISE_100FULL); | |
| if (tp->mii.supports_gmii) { | |
| gbcr = r8152_mdio_read(tp, MII_CTRL1000); | |
| gbcr &= ~(ADVERTISE_1000FULL | ADVERTISE_1000HALF); | |
| } else { | |
| gbcr = 0; | |
| } | |
| if (autoneg == AUTONEG_DISABLE) { | |
| if (speed == SPEED_10) { | |
| bmcr = 0; | |
| anar |= ADVERTISE_10HALF | ADVERTISE_10FULL; | |
| } else if (speed == SPEED_100) { | |
| bmcr = BMCR_SPEED100; | |
| anar |= ADVERTISE_100HALF | ADVERTISE_100FULL; | |
| } else if (speed == SPEED_1000 && tp->mii.supports_gmii) { | |
| bmcr = BMCR_SPEED1000; | |
| gbcr |= ADVERTISE_1000FULL | ADVERTISE_1000HALF; | |
| } else { | |
| ret = -EINVAL; | |
| goto out; | |
| } | |
| if (duplex == DUPLEX_FULL) | |
| bmcr |= BMCR_FULLDPLX; | |
| } else { | |
| if (speed == SPEED_10) { | |
| if (duplex == DUPLEX_FULL) | |
| anar |= ADVERTISE_10HALF | ADVERTISE_10FULL; | |
| else | |
| anar |= ADVERTISE_10HALF; | |
| } else if (speed == SPEED_100) { | |
| if (duplex == DUPLEX_FULL) { | |
| anar |= ADVERTISE_10HALF | ADVERTISE_10FULL; | |
| anar |= ADVERTISE_100HALF | ADVERTISE_100FULL; | |
| } else { | |
| anar |= ADVERTISE_10HALF; | |
| anar |= ADVERTISE_100HALF; | |
| } | |
| } else if (speed == SPEED_1000 && tp->mii.supports_gmii) { | |
| if (duplex == DUPLEX_FULL) { | |
| anar |= ADVERTISE_10HALF | ADVERTISE_10FULL; | |
| anar |= ADVERTISE_100HALF | ADVERTISE_100FULL; | |
| gbcr |= ADVERTISE_1000FULL | ADVERTISE_1000HALF; | |
| } else { | |
| anar |= ADVERTISE_10HALF; | |
| anar |= ADVERTISE_100HALF; | |
| gbcr |= ADVERTISE_1000HALF; | |
| } | |
| } else { | |
| ret = -EINVAL; | |
| goto out; | |
| } | |
| bmcr = BMCR_ANENABLE | BMCR_ANRESTART; | |
| } | |
| if (test_bit(PHY_RESET, &tp->flags)) | |
| bmcr |= BMCR_RESET; | |
| if (tp->mii.supports_gmii) | |
| r8152_mdio_write(tp, MII_CTRL1000, gbcr); | |
| r8152_mdio_write(tp, MII_ADVERTISE, anar); | |
| r8152_mdio_write(tp, MII_BMCR, bmcr); | |
| if (test_bit(PHY_RESET, &tp->flags)) { | |
| int i; | |
| clear_bit(PHY_RESET, &tp->flags); | |
| for (i = 0; i < 50; i++) { | |
| msleep(20); | |
| if ((r8152_mdio_read(tp, MII_BMCR) & BMCR_RESET) == 0) | |
| break; | |
| } | |
| } | |
| out: | |
| return ret; | |
| } | |
| static void rtl8152_up(struct r8152 *tp) | |
| { | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags)) | |
| return; | |
| r8152b_disable_aldps(tp); | |
| r8152b_exit_oob(tp); | |
| r8152b_enable_aldps(tp); | |
| } | |
| static void rtl8152_down(struct r8152 *tp) | |
| { | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags)) { | |
| rtl_drop_queued_tx(tp); | |
| return; | |
| } | |
| r8152_power_cut_en(tp, false); | |
| r8152b_disable_aldps(tp); | |
| r8152b_enter_oob(tp); | |
| r8152b_enable_aldps(tp); | |
| } | |
| static void rtl8153_up(struct r8152 *tp) | |
| { | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags)) | |
| return; | |
| r8153_u1u2en(tp, false); | |
| r8153_disable_aldps(tp); | |
| r8153_first_init(tp); | |
| r8153_enable_aldps(tp); | |
| r8153_u2p3en(tp, true); | |
| r8153_u1u2en(tp, true); | |
| usb_enable_lpm(tp->udev); | |
| } | |
| static void rtl8153_down(struct r8152 *tp) | |
| { | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags)) { | |
| rtl_drop_queued_tx(tp); | |
| return; | |
| } | |
| r8153_u1u2en(tp, false); | |
| r8153_u2p3en(tp, false); | |
| r8153_power_cut_en(tp, false); | |
| r8153_disable_aldps(tp); | |
| r8153_enter_oob(tp); | |
| r8153_enable_aldps(tp); | |
| } | |
| static bool rtl8152_in_nway(struct r8152 *tp) | |
| { | |
| u16 nway_state; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_OCP_GPHY_BASE, 0x2000); | |
| tp->ocp_base = 0x2000; | |
| ocp_write_byte(tp, MCU_TYPE_PLA, 0xb014, 0x4c); /* phy state */ | |
| nway_state = ocp_read_word(tp, MCU_TYPE_PLA, 0xb01a); | |
| /* bit 15: TXDIS_STATE, bit 14: ABD_STATE */ | |
| if (nway_state & 0xc000) | |
| return false; | |
| else | |
| return true; | |
| } | |
| static bool rtl8153_in_nway(struct r8152 *tp) | |
| { | |
| u16 phy_state = ocp_reg_read(tp, OCP_PHY_STATE) & 0xff; | |
| if (phy_state == TXDIS_STATE || phy_state == ABD_STATE) | |
| return false; | |
| else | |
| return true; | |
| } | |
| static void set_carrier(struct r8152 *tp) | |
| { | |
| struct net_device *netdev = tp->netdev; | |
| u8 speed; | |
| clear_bit(RTL8152_LINK_CHG, &tp->flags); | |
| speed = rtl8152_get_speed(tp); | |
| if (speed & LINK_STATUS) { | |
| if (!netif_carrier_ok(netdev)) { | |
| tp->rtl_ops.enable(tp); | |
| set_bit(RTL8152_SET_RX_MODE, &tp->flags); | |
| napi_disable(&tp->napi); | |
| netif_carrier_on(netdev); | |
| rtl_start_rx(tp); | |
| napi_enable(&tp->napi); | |
| } | |
| } else { | |
| if (netif_carrier_ok(netdev)) { | |
| netif_carrier_off(netdev); | |
| napi_disable(&tp->napi); | |
| tp->rtl_ops.disable(tp); | |
| napi_enable(&tp->napi); | |
| } | |
| } | |
| } | |
| static void rtl_work_func_t(struct work_struct *work) | |
| { | |
| struct r8152 *tp = container_of(work, struct r8152, schedule.work); | |
| /* If the device is unplugged or !netif_running(), the workqueue | |
| * doesn't need to wake the device, and could return directly. | |
| */ | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags) || !netif_running(tp->netdev)) | |
| return; | |
| if (usb_autopm_get_interface(tp->intf) < 0) | |
| return; | |
| if (!test_bit(WORK_ENABLE, &tp->flags)) | |
| goto out1; | |
| if (!mutex_trylock(&tp->control)) { | |
| schedule_delayed_work(&tp->schedule, 0); | |
| goto out1; | |
| } | |
| if (test_bit(RTL8152_LINK_CHG, &tp->flags)) | |
| set_carrier(tp); | |
| if (test_bit(RTL8152_SET_RX_MODE, &tp->flags)) | |
| _rtl8152_set_rx_mode(tp->netdev); | |
| /* don't schedule napi before linking */ | |
| if (test_bit(SCHEDULE_NAPI, &tp->flags) && | |
| netif_carrier_ok(tp->netdev)) { | |
| clear_bit(SCHEDULE_NAPI, &tp->flags); | |
| napi_schedule(&tp->napi); | |
| } | |
| if (test_bit(PHY_RESET, &tp->flags)) | |
| rtl_phy_reset(tp); | |
| mutex_unlock(&tp->control); | |
| out1: | |
| usb_autopm_put_interface(tp->intf); | |
| } | |
| static int rtl8152_open(struct net_device *netdev) | |
| { | |
| struct r8152 *tp = netdev_priv(netdev); | |
| int res = 0; | |
| res = alloc_all_mem(tp); | |
| if (res) | |
| goto out; | |
| netif_carrier_off(netdev); | |
| res = usb_autopm_get_interface(tp->intf); | |
| if (res < 0) { | |
| free_all_mem(tp); | |
| goto out; | |
| } | |
| mutex_lock(&tp->control); | |
| tp->rtl_ops.up(tp); | |
| rtl8152_set_speed(tp, AUTONEG_ENABLE, | |
| tp->mii.supports_gmii ? SPEED_1000 : SPEED_100, | |
| DUPLEX_FULL); | |
| netif_carrier_off(netdev); | |
| netif_start_queue(netdev); | |
| set_bit(WORK_ENABLE, &tp->flags); | |
| res = usb_submit_urb(tp->intr_urb, GFP_KERNEL); | |
| if (res) { | |
| if (res == -ENODEV) | |
| netif_device_detach(tp->netdev); | |
| netif_warn(tp, ifup, netdev, "intr_urb submit failed: %d\n", | |
| res); | |
| free_all_mem(tp); | |
| } else { | |
| napi_enable(&tp->napi); | |
| } | |
| mutex_unlock(&tp->control); | |
| usb_autopm_put_interface(tp->intf); | |
| out: | |
| return res; | |
| } | |
| static int rtl8152_close(struct net_device *netdev) | |
| { | |
| struct r8152 *tp = netdev_priv(netdev); | |
| int res = 0; | |
| napi_disable(&tp->napi); | |
| clear_bit(WORK_ENABLE, &tp->flags); | |
| usb_kill_urb(tp->intr_urb); | |
| cancel_delayed_work_sync(&tp->schedule); | |
| netif_stop_queue(netdev); | |
| res = usb_autopm_get_interface(tp->intf); | |
| if (res < 0 || test_bit(RTL8152_UNPLUG, &tp->flags)) { | |
| rtl_drop_queued_tx(tp); | |
| rtl_stop_rx(tp); | |
| } else { | |
| mutex_lock(&tp->control); | |
| tp->rtl_ops.down(tp); | |
| mutex_unlock(&tp->control); | |
| usb_autopm_put_interface(tp->intf); | |
| } | |
| free_all_mem(tp); | |
| return res; | |
| } | |
| static inline void r8152_mmd_indirect(struct r8152 *tp, u16 dev, u16 reg) | |
| { | |
| ocp_reg_write(tp, OCP_EEE_AR, FUN_ADDR | dev); | |
| ocp_reg_write(tp, OCP_EEE_DATA, reg); | |
| ocp_reg_write(tp, OCP_EEE_AR, FUN_DATA | dev); | |
| } | |
| static u16 r8152_mmd_read(struct r8152 *tp, u16 dev, u16 reg) | |
| { | |
| u16 data; | |
| r8152_mmd_indirect(tp, dev, reg); | |
| data = ocp_reg_read(tp, OCP_EEE_DATA); | |
| ocp_reg_write(tp, OCP_EEE_AR, 0x0000); | |
| return data; | |
| } | |
| static void r8152_mmd_write(struct r8152 *tp, u16 dev, u16 reg, u16 data) | |
| { | |
| r8152_mmd_indirect(tp, dev, reg); | |
| ocp_reg_write(tp, OCP_EEE_DATA, data); | |
| ocp_reg_write(tp, OCP_EEE_AR, 0x0000); | |
| } | |
| static void r8152_eee_en(struct r8152 *tp, bool enable) | |
| { | |
| u16 config1, config2, config3; | |
| u32 ocp_data; | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_EEE_CR); | |
| config1 = ocp_reg_read(tp, OCP_EEE_CONFIG1) & ~sd_rise_time_mask; | |
| config2 = ocp_reg_read(tp, OCP_EEE_CONFIG2); | |
| config3 = ocp_reg_read(tp, OCP_EEE_CONFIG3) & ~fast_snr_mask; | |
| if (enable) { | |
| ocp_data |= EEE_RX_EN | EEE_TX_EN; | |
| config1 |= EEE_10_CAP | EEE_NWAY_EN | TX_QUIET_EN | RX_QUIET_EN; | |
| config1 |= sd_rise_time(1); | |
| config2 |= RG_DACQUIET_EN | RG_LDVQUIET_EN; | |
| config3 |= fast_snr(42); | |
| } else { | |
| ocp_data &= ~(EEE_RX_EN | EEE_TX_EN); | |
| config1 &= ~(EEE_10_CAP | EEE_NWAY_EN | TX_QUIET_EN | | |
| RX_QUIET_EN); | |
| config1 |= sd_rise_time(7); | |
| config2 &= ~(RG_DACQUIET_EN | RG_LDVQUIET_EN); | |
| config3 |= fast_snr(511); | |
| } | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_EEE_CR, ocp_data); | |
| ocp_reg_write(tp, OCP_EEE_CONFIG1, config1); | |
| ocp_reg_write(tp, OCP_EEE_CONFIG2, config2); | |
| ocp_reg_write(tp, OCP_EEE_CONFIG3, config3); | |
| } | |
| static void r8152b_enable_eee(struct r8152 *tp) | |
| { | |
| r8152_eee_en(tp, true); | |
| r8152_mmd_write(tp, MDIO_MMD_AN, MDIO_AN_EEE_ADV, MDIO_EEE_100TX); | |
| } | |
| static void r8153_eee_en(struct r8152 *tp, bool enable) | |
| { | |
| u32 ocp_data; | |
| u16 config; | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_EEE_CR); | |
| config = ocp_reg_read(tp, OCP_EEE_CFG); | |
| if (enable) { | |
| ocp_data |= EEE_RX_EN | EEE_TX_EN; | |
| config |= EEE10_EN; | |
| } else { | |
| ocp_data &= ~(EEE_RX_EN | EEE_TX_EN); | |
| config &= ~EEE10_EN; | |
| } | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_EEE_CR, ocp_data); | |
| ocp_reg_write(tp, OCP_EEE_CFG, config); | |
| } | |
| static void r8153_enable_eee(struct r8152 *tp) | |
| { | |
| r8153_eee_en(tp, true); | |
| ocp_reg_write(tp, OCP_EEE_ADV, MDIO_EEE_1000T | MDIO_EEE_100TX); | |
| } | |
| static void r8152b_enable_fc(struct r8152 *tp) | |
| { | |
| u16 anar; | |
| anar = r8152_mdio_read(tp, MII_ADVERTISE); | |
| anar |= ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM; | |
| r8152_mdio_write(tp, MII_ADVERTISE, anar); | |
| } | |
| static void rtl_tally_reset(struct r8152 *tp) | |
| { | |
| u32 ocp_data; | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_RSTTALLY); | |
| ocp_data |= TALLY_RESET; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_RSTTALLY, ocp_data); | |
| } | |
| static void r8152b_init(struct r8152 *tp) | |
| { | |
| u32 ocp_data; | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags)) | |
| return; | |
| r8152b_disable_aldps(tp); | |
| if (tp->version == RTL_VER_01) { | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_LED_FEATURE); | |
| ocp_data &= ~LED_MODE_MASK; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_LED_FEATURE, ocp_data); | |
| } | |
| r8152_power_cut_en(tp, false); | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_PHY_PWR); | |
| ocp_data |= TX_10M_IDLE_EN | PFM_PWM_SWITCH; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_PHY_PWR, ocp_data); | |
| ocp_data = ocp_read_dword(tp, MCU_TYPE_PLA, PLA_MAC_PWR_CTRL); | |
| ocp_data &= ~MCU_CLK_RATIO_MASK; | |
| ocp_data |= MCU_CLK_RATIO | D3_CLK_GATED_EN; | |
| ocp_write_dword(tp, MCU_TYPE_PLA, PLA_MAC_PWR_CTRL, ocp_data); | |
| ocp_data = GPHY_STS_MSK | SPEED_DOWN_MSK | | |
| SPDWN_RXDV_MSK | SPDWN_LINKCHG_MSK; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_GPHY_INTR_IMR, ocp_data); | |
| r8152b_enable_eee(tp); | |
| r8152b_enable_aldps(tp); | |
| r8152b_enable_fc(tp); | |
| rtl_tally_reset(tp); | |
| /* enable rx aggregation */ | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_USB, USB_USB_CTRL); | |
| ocp_data &= ~(RX_AGG_DISABLE | RX_ZERO_EN); | |
| ocp_write_word(tp, MCU_TYPE_USB, USB_USB_CTRL, ocp_data); | |
| } | |
| static void r8153_init(struct r8152 *tp) | |
| { | |
| u32 ocp_data; | |
| int i; | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags)) | |
| return; | |
| r8153_disable_aldps(tp); | |
| r8153_u1u2en(tp, false); | |
| for (i = 0; i < 500; i++) { | |
| if (ocp_read_word(tp, MCU_TYPE_PLA, PLA_BOOT_CTRL) & | |
| AUTOLOAD_DONE) | |
| break; | |
| msleep(20); | |
| } | |
| for (i = 0; i < 500; i++) { | |
| ocp_data = ocp_reg_read(tp, OCP_PHY_STATUS) & PHY_STAT_MASK; | |
| if (ocp_data == PHY_STAT_LAN_ON || ocp_data == PHY_STAT_PWRDN) | |
| break; | |
| msleep(20); | |
| } | |
| usb_disable_lpm(tp->udev); | |
| r8153_u2p3en(tp, false); | |
| if (tp->version == RTL_VER_04) { | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_USB, USB_SSPHYLINK2); | |
| ocp_data &= ~pwd_dn_scale_mask; | |
| ocp_data |= pwd_dn_scale(96); | |
| ocp_write_word(tp, MCU_TYPE_USB, USB_SSPHYLINK2, ocp_data); | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_USB, USB_USB2PHY); | |
| ocp_data |= USB2PHY_L1 | USB2PHY_SUSPEND; | |
| ocp_write_byte(tp, MCU_TYPE_USB, USB_USB2PHY, ocp_data); | |
| } else if (tp->version == RTL_VER_05) { | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_DMY_REG0); | |
| ocp_data &= ~ECM_ALDPS; | |
| ocp_write_byte(tp, MCU_TYPE_PLA, PLA_DMY_REG0, ocp_data); | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_USB, USB_CSR_DUMMY1); | |
| if (ocp_read_word(tp, MCU_TYPE_USB, USB_BURST_SIZE) == 0) | |
| ocp_data &= ~DYNAMIC_BURST; | |
| else | |
| ocp_data |= DYNAMIC_BURST; | |
| ocp_write_byte(tp, MCU_TYPE_USB, USB_CSR_DUMMY1, ocp_data); | |
| } else if (tp->version == RTL_VER_06) { | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_USB, USB_CSR_DUMMY1); | |
| if (ocp_read_word(tp, MCU_TYPE_USB, USB_BURST_SIZE) == 0) | |
| ocp_data &= ~DYNAMIC_BURST; | |
| else | |
| ocp_data |= DYNAMIC_BURST; | |
| ocp_write_byte(tp, MCU_TYPE_USB, USB_CSR_DUMMY1, ocp_data); | |
| } | |
| ocp_data = ocp_read_byte(tp, MCU_TYPE_USB, USB_CSR_DUMMY2); | |
| ocp_data |= EP4_FULL_FC; | |
| ocp_write_byte(tp, MCU_TYPE_USB, USB_CSR_DUMMY2, ocp_data); | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_USB, USB_WDT11_CTRL); | |
| ocp_data &= ~TIMER11_EN; | |
| ocp_write_word(tp, MCU_TYPE_USB, USB_WDT11_CTRL, ocp_data); | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_LED_FEATURE); | |
| ocp_data &= ~LED_MODE_MASK; | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_LED_FEATURE, ocp_data); | |
| ocp_data = FIFO_EMPTY_1FB | ROK_EXIT_LPM; | |
| if (tp->version == RTL_VER_04 && tp->udev->speed != USB_SPEED_SUPER) | |
| ocp_data |= LPM_TIMER_500MS; | |
| else | |
| ocp_data |= LPM_TIMER_500US; | |
| ocp_write_byte(tp, MCU_TYPE_USB, USB_LPM_CTRL, ocp_data); | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_USB, USB_AFE_CTRL2); | |
| ocp_data &= ~SEN_VAL_MASK; | |
| ocp_data |= SEN_VAL_NORMAL | SEL_RXIDLE; | |
| ocp_write_word(tp, MCU_TYPE_USB, USB_AFE_CTRL2, ocp_data); | |
| ocp_write_word(tp, MCU_TYPE_USB, USB_CONNECT_TIMER, 0x0001); | |
| r8153_power_cut_en(tp, false); | |
| r8153_u1u2en(tp, true); | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_MAC_PWR_CTRL, ALDPS_SPDWN_RATIO); | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_MAC_PWR_CTRL2, EEE_SPDWN_RATIO); | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_MAC_PWR_CTRL3, | |
| PKT_AVAIL_SPDWN_EN | SUSPEND_SPDWN_EN | | |
| U1U2_SPDWN_EN | L1_SPDWN_EN); | |
| ocp_write_word(tp, MCU_TYPE_PLA, PLA_MAC_PWR_CTRL4, | |
| PWRSAVE_SPDWN_EN | RXDV_SPDWN_EN | TX10MIDLE_EN | | |
| TP100_SPDWN_EN | TP500_SPDWN_EN | TP1000_SPDWN_EN | | |
| EEE_SPDWN_EN); | |
| r8153_enable_eee(tp); | |
| r8153_enable_aldps(tp); | |
| r8152b_enable_fc(tp); | |
| rtl_tally_reset(tp); | |
| r8153_u2p3en(tp, true); | |
| } | |
| static int rtl8152_pre_reset(struct usb_interface *intf) | |
| { | |
| struct r8152 *tp = usb_get_intfdata(intf); | |
| struct net_device *netdev; | |
| if (!tp) | |
| return 0; | |
| netdev = tp->netdev; | |
| if (!netif_running(netdev)) | |
| return 0; | |
| napi_disable(&tp->napi); | |
| clear_bit(WORK_ENABLE, &tp->flags); | |
| usb_kill_urb(tp->intr_urb); | |
| cancel_delayed_work_sync(&tp->schedule); | |
| if (netif_carrier_ok(netdev)) { | |
| netif_stop_queue(netdev); | |
| mutex_lock(&tp->control); | |
| tp->rtl_ops.disable(tp); | |
| mutex_unlock(&tp->control); | |
| } | |
| return 0; | |
| } | |
| static int rtl8152_post_reset(struct usb_interface *intf) | |
| { | |
| struct r8152 *tp = usb_get_intfdata(intf); | |
| struct net_device *netdev; | |
| if (!tp) | |
| return 0; | |
| netdev = tp->netdev; | |
| if (!netif_running(netdev)) | |
| return 0; | |
| set_bit(WORK_ENABLE, &tp->flags); | |
| if (netif_carrier_ok(netdev)) { | |
| mutex_lock(&tp->control); | |
| tp->rtl_ops.enable(tp); | |
| rtl8152_set_rx_mode(netdev); | |
| mutex_unlock(&tp->control); | |
| netif_wake_queue(netdev); | |
| } | |
| napi_enable(&tp->napi); | |
| return 0; | |
| } | |
| static bool delay_autosuspend(struct r8152 *tp) | |
| { | |
| bool sw_linking = !!netif_carrier_ok(tp->netdev); | |
| bool hw_linking = !!(rtl8152_get_speed(tp) & LINK_STATUS); | |
| /* This means a linking change occurs and the driver doesn't detect it, | |
| * yet. If the driver has disabled tx/rx and hw is linking on, the | |
| * device wouldn't wake up by receiving any packet. | |
| */ | |
| if (work_busy(&tp->schedule.work) || sw_linking != hw_linking) | |
| return true; | |
| /* If the linking down is occurred by nway, the device may miss the | |
| * linking change event. And it wouldn't wake when linking on. | |
| */ | |
| if (!sw_linking && tp->rtl_ops.in_nway(tp)) | |
| return true; | |
| else | |
| return false; | |
| } | |
| static int rtl8152_suspend(struct usb_interface *intf, pm_message_t message) | |
| { | |
| struct r8152 *tp = usb_get_intfdata(intf); | |
| struct net_device *netdev = tp->netdev; | |
| int ret = 0; | |
| mutex_lock(&tp->control); | |
| if (PMSG_IS_AUTO(message)) { | |
| if (netif_running(netdev) && delay_autosuspend(tp)) { | |
| ret = -EBUSY; | |
| goto out1; | |
| } | |
| set_bit(SELECTIVE_SUSPEND, &tp->flags); | |
| } else { | |
| netif_device_detach(netdev); | |
| } | |
| if (netif_running(netdev) && test_bit(WORK_ENABLE, &tp->flags)) { | |
| clear_bit(WORK_ENABLE, &tp->flags); | |
| usb_kill_urb(tp->intr_urb); | |
| napi_disable(&tp->napi); | |
| if (test_bit(SELECTIVE_SUSPEND, &tp->flags)) { | |
| rtl_stop_rx(tp); | |
| rtl_runtime_suspend_enable(tp, true); | |
| } else { | |
| cancel_delayed_work_sync(&tp->schedule); | |
| tp->rtl_ops.down(tp); | |
| } | |
| napi_enable(&tp->napi); | |
| } | |
| out1: | |
| mutex_unlock(&tp->control); | |
| return ret; | |
| } | |
| static int rtl8152_resume(struct usb_interface *intf) | |
| { | |
| struct r8152 *tp = usb_get_intfdata(intf); | |
| mutex_lock(&tp->control); | |
| if (!test_bit(SELECTIVE_SUSPEND, &tp->flags)) { | |
| tp->rtl_ops.init(tp); | |
| netif_device_attach(tp->netdev); | |
| } | |
| if (netif_running(tp->netdev) && tp->netdev->flags & IFF_UP) { | |
| if (test_bit(SELECTIVE_SUSPEND, &tp->flags)) { | |
| rtl_runtime_suspend_enable(tp, false); | |
| clear_bit(SELECTIVE_SUSPEND, &tp->flags); | |
| napi_disable(&tp->napi); | |
| set_bit(WORK_ENABLE, &tp->flags); | |
| if (netif_carrier_ok(tp->netdev)) | |
| rtl_start_rx(tp); | |
| napi_enable(&tp->napi); | |
| } else { | |
| tp->rtl_ops.up(tp); | |
| rtl8152_set_speed(tp, AUTONEG_ENABLE, | |
| tp->mii.supports_gmii ? | |
| SPEED_1000 : SPEED_100, | |
| DUPLEX_FULL); | |
| netif_carrier_off(tp->netdev); | |
| set_bit(WORK_ENABLE, &tp->flags); | |
| } | |
| usb_submit_urb(tp->intr_urb, GFP_KERNEL); | |
| } else if (test_bit(SELECTIVE_SUSPEND, &tp->flags)) { | |
| if (tp->netdev->flags & IFF_UP) | |
| rtl_runtime_suspend_enable(tp, false); | |
| clear_bit(SELECTIVE_SUSPEND, &tp->flags); | |
| } | |
| mutex_unlock(&tp->control); | |
| return 0; | |
| } | |
| static int rtl8152_reset_resume(struct usb_interface *intf) | |
| { | |
| struct r8152 *tp = usb_get_intfdata(intf); | |
| clear_bit(SELECTIVE_SUSPEND, &tp->flags); | |
| return rtl8152_resume(intf); | |
| } | |
| static void rtl8152_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol) | |
| { | |
| struct r8152 *tp = netdev_priv(dev); | |
| if (usb_autopm_get_interface(tp->intf) < 0) | |
| return; | |
| if (!rtl_can_wakeup(tp)) { | |
| wol->supported = 0; | |
| wol->wolopts = 0; | |
| } else { | |
| mutex_lock(&tp->control); | |
| wol->supported = WAKE_ANY; | |
| wol->wolopts = __rtl_get_wol(tp); | |
| mutex_unlock(&tp->control); | |
| } | |
| usb_autopm_put_interface(tp->intf); | |
| } | |
| static int rtl8152_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol) | |
| { | |
| struct r8152 *tp = netdev_priv(dev); | |
| int ret; | |
| if (!rtl_can_wakeup(tp)) | |
| return -EOPNOTSUPP; | |
| ret = usb_autopm_get_interface(tp->intf); | |
| if (ret < 0) | |
| goto out_set_wol; | |
| mutex_lock(&tp->control); | |
| __rtl_set_wol(tp, wol->wolopts); | |
| tp->saved_wolopts = wol->wolopts & WAKE_ANY; | |
| mutex_unlock(&tp->control); | |
| usb_autopm_put_interface(tp->intf); | |
| out_set_wol: | |
| return ret; | |
| } | |
| static u32 rtl8152_get_msglevel(struct net_device *dev) | |
| { | |
| struct r8152 *tp = netdev_priv(dev); | |
| return tp->msg_enable; | |
| } | |
| static void rtl8152_set_msglevel(struct net_device *dev, u32 value) | |
| { | |
| struct r8152 *tp = netdev_priv(dev); | |
| tp->msg_enable = value; | |
| } | |
| static void rtl8152_get_drvinfo(struct net_device *netdev, | |
| struct ethtool_drvinfo *info) | |
| { | |
| struct r8152 *tp = netdev_priv(netdev); | |
| strlcpy(info->driver, MODULENAME, sizeof(info->driver)); | |
| strlcpy(info->version, DRIVER_VERSION, sizeof(info->version)); | |
| usb_make_path(tp->udev, info->bus_info, sizeof(info->bus_info)); | |
| } | |
| static | |
| int rtl8152_get_settings(struct net_device *netdev, struct ethtool_cmd *cmd) | |
| { | |
| struct r8152 *tp = netdev_priv(netdev); | |
| int ret; | |
| if (!tp->mii.mdio_read) | |
| return -EOPNOTSUPP; | |
| ret = usb_autopm_get_interface(tp->intf); | |
| if (ret < 0) | |
| goto out; | |
| mutex_lock(&tp->control); | |
| ret = mii_ethtool_gset(&tp->mii, cmd); | |
| mutex_unlock(&tp->control); | |
| usb_autopm_put_interface(tp->intf); | |
| out: | |
| return ret; | |
| } | |
| static int rtl8152_set_settings(struct net_device *dev, struct ethtool_cmd *cmd) | |
| { | |
| struct r8152 *tp = netdev_priv(dev); | |
| int ret; | |
| ret = usb_autopm_get_interface(tp->intf); | |
| if (ret < 0) | |
| goto out; | |
| mutex_lock(&tp->control); | |
| ret = rtl8152_set_speed(tp, cmd->autoneg, cmd->speed, cmd->duplex); | |
| mutex_unlock(&tp->control); | |
| usb_autopm_put_interface(tp->intf); | |
| out: | |
| return ret; | |
| } | |
| static const char rtl8152_gstrings[][ETH_GSTRING_LEN] = { | |
| "tx_packets", | |
| "rx_packets", | |
| "tx_errors", | |
| "rx_errors", | |
| "rx_missed", | |
| "align_errors", | |
| "tx_single_collisions", | |
| "tx_multi_collisions", | |
| "rx_unicast", | |
| "rx_broadcast", | |
| "rx_multicast", | |
| "tx_aborted", | |
| "tx_underrun", | |
| }; | |
| static int rtl8152_get_sset_count(struct net_device *dev, int sset) | |
| { | |
| switch (sset) { | |
| case ETH_SS_STATS: | |
| return ARRAY_SIZE(rtl8152_gstrings); | |
| default: | |
| return -EOPNOTSUPP; | |
| } | |
| } | |
| static void rtl8152_get_ethtool_stats(struct net_device *dev, | |
| struct ethtool_stats *stats, u64 *data) | |
| { | |
| struct r8152 *tp = netdev_priv(dev); | |
| struct tally_counter tally; | |
| if (usb_autopm_get_interface(tp->intf) < 0) | |
| return; | |
| generic_ocp_read(tp, PLA_TALLYCNT, sizeof(tally), &tally, MCU_TYPE_PLA); | |
| usb_autopm_put_interface(tp->intf); | |
| data[0] = le64_to_cpu(tally.tx_packets); | |
| data[1] = le64_to_cpu(tally.rx_packets); | |
| data[2] = le64_to_cpu(tally.tx_errors); | |
| data[3] = le32_to_cpu(tally.rx_errors); | |
| data[4] = le16_to_cpu(tally.rx_missed); | |
| data[5] = le16_to_cpu(tally.align_errors); | |
| data[6] = le32_to_cpu(tally.tx_one_collision); | |
| data[7] = le32_to_cpu(tally.tx_multi_collision); | |
| data[8] = le64_to_cpu(tally.rx_unicast); | |
| data[9] = le64_to_cpu(tally.rx_broadcast); | |
| data[10] = le32_to_cpu(tally.rx_multicast); | |
| data[11] = le16_to_cpu(tally.tx_aborted); | |
| data[12] = le16_to_cpu(tally.tx_underrun); | |
| } | |
| static void rtl8152_get_strings(struct net_device *dev, u32 stringset, u8 *data) | |
| { | |
| switch (stringset) { | |
| case ETH_SS_STATS: | |
| memcpy(data, *rtl8152_gstrings, sizeof(rtl8152_gstrings)); | |
| break; | |
| } | |
| } | |
| static int r8152_get_eee(struct r8152 *tp, struct ethtool_eee *eee) | |
| { | |
| u32 ocp_data, lp, adv, supported = 0; | |
| u16 val; | |
| val = r8152_mmd_read(tp, MDIO_MMD_PCS, MDIO_PCS_EEE_ABLE); | |
| supported = mmd_eee_cap_to_ethtool_sup_t(val); | |
| val = r8152_mmd_read(tp, MDIO_MMD_AN, MDIO_AN_EEE_ADV); | |
| adv = mmd_eee_adv_to_ethtool_adv_t(val); | |
| val = r8152_mmd_read(tp, MDIO_MMD_AN, MDIO_AN_EEE_LPABLE); | |
| lp = mmd_eee_adv_to_ethtool_adv_t(val); | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_EEE_CR); | |
| ocp_data &= EEE_RX_EN | EEE_TX_EN; | |
| eee->eee_enabled = !!ocp_data; | |
| eee->eee_active = !!(supported & adv & lp); | |
| eee->supported = supported; | |
| eee->advertised = adv; | |
| eee->lp_advertised = lp; | |
| return 0; | |
| } | |
| static int r8152_set_eee(struct r8152 *tp, struct ethtool_eee *eee) | |
| { | |
| u16 val = ethtool_adv_to_mmd_eee_adv_t(eee->advertised); | |
| r8152_eee_en(tp, eee->eee_enabled); | |
| if (!eee->eee_enabled) | |
| val = 0; | |
| r8152_mmd_write(tp, MDIO_MMD_AN, MDIO_AN_EEE_ADV, val); | |
| return 0; | |
| } | |
| static int r8153_get_eee(struct r8152 *tp, struct ethtool_eee *eee) | |
| { | |
| u32 ocp_data, lp, adv, supported = 0; | |
| u16 val; | |
| val = ocp_reg_read(tp, OCP_EEE_ABLE); | |
| supported = mmd_eee_cap_to_ethtool_sup_t(val); | |
| val = ocp_reg_read(tp, OCP_EEE_ADV); | |
| adv = mmd_eee_adv_to_ethtool_adv_t(val); | |
| val = ocp_reg_read(tp, OCP_EEE_LPABLE); | |
| lp = mmd_eee_adv_to_ethtool_adv_t(val); | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_EEE_CR); | |
| ocp_data &= EEE_RX_EN | EEE_TX_EN; | |
| eee->eee_enabled = !!ocp_data; | |
| eee->eee_active = !!(supported & adv & lp); | |
| eee->supported = supported; | |
| eee->advertised = adv; | |
| eee->lp_advertised = lp; | |
| return 0; | |
| } | |
| static int r8153_set_eee(struct r8152 *tp, struct ethtool_eee *eee) | |
| { | |
| u16 val = ethtool_adv_to_mmd_eee_adv_t(eee->advertised); | |
| r8153_eee_en(tp, eee->eee_enabled); | |
| if (!eee->eee_enabled) | |
| val = 0; | |
| ocp_reg_write(tp, OCP_EEE_ADV, val); | |
| return 0; | |
| } | |
| static int | |
| rtl_ethtool_get_eee(struct net_device *net, struct ethtool_eee *edata) | |
| { | |
| struct r8152 *tp = netdev_priv(net); | |
| int ret; | |
| ret = usb_autopm_get_interface(tp->intf); | |
| if (ret < 0) | |
| goto out; | |
| mutex_lock(&tp->control); | |
| ret = tp->rtl_ops.eee_get(tp, edata); | |
| mutex_unlock(&tp->control); | |
| usb_autopm_put_interface(tp->intf); | |
| out: | |
| return ret; | |
| } | |
| static int | |
| rtl_ethtool_set_eee(struct net_device *net, struct ethtool_eee *edata) | |
| { | |
| struct r8152 *tp = netdev_priv(net); | |
| int ret; | |
| ret = usb_autopm_get_interface(tp->intf); | |
| if (ret < 0) | |
| goto out; | |
| mutex_lock(&tp->control); | |
| ret = tp->rtl_ops.eee_set(tp, edata); | |
| if (!ret) | |
| ret = mii_nway_restart(&tp->mii); | |
| mutex_unlock(&tp->control); | |
| usb_autopm_put_interface(tp->intf); | |
| out: | |
| return ret; | |
| } | |
| static int rtl8152_nway_reset(struct net_device *dev) | |
| { | |
| struct r8152 *tp = netdev_priv(dev); | |
| int ret; | |
| ret = usb_autopm_get_interface(tp->intf); | |
| if (ret < 0) | |
| goto out; | |
| mutex_lock(&tp->control); | |
| ret = mii_nway_restart(&tp->mii); | |
| mutex_unlock(&tp->control); | |
| usb_autopm_put_interface(tp->intf); | |
| out: | |
| return ret; | |
| } | |
| static int rtl8152_get_coalesce(struct net_device *netdev, | |
| struct ethtool_coalesce *coalesce) | |
| { | |
| struct r8152 *tp = netdev_priv(netdev); | |
| switch (tp->version) { | |
| case RTL_VER_01: | |
| case RTL_VER_02: | |
| return -EOPNOTSUPP; | |
| default: | |
| break; | |
| } | |
| coalesce->rx_coalesce_usecs = tp->coalesce; | |
| return 0; | |
| } | |
| static int rtl8152_set_coalesce(struct net_device *netdev, | |
| struct ethtool_coalesce *coalesce) | |
| { | |
| struct r8152 *tp = netdev_priv(netdev); | |
| int ret; | |
| switch (tp->version) { | |
| case RTL_VER_01: | |
| case RTL_VER_02: | |
| return -EOPNOTSUPP; | |
| default: | |
| break; | |
| } | |
| if (coalesce->rx_coalesce_usecs > COALESCE_SLOW) | |
| return -EINVAL; | |
| ret = usb_autopm_get_interface(tp->intf); | |
| if (ret < 0) | |
| return ret; | |
| mutex_lock(&tp->control); | |
| if (tp->coalesce != coalesce->rx_coalesce_usecs) { | |
| tp->coalesce = coalesce->rx_coalesce_usecs; | |
| if (netif_running(tp->netdev) && netif_carrier_ok(netdev)) | |
| r8153_set_rx_early_timeout(tp); | |
| } | |
| mutex_unlock(&tp->control); | |
| usb_autopm_put_interface(tp->intf); | |
| return ret; | |
| } | |
| static struct ethtool_ops ops = { | |
| .get_drvinfo = rtl8152_get_drvinfo, | |
| .get_settings = rtl8152_get_settings, | |
| .set_settings = rtl8152_set_settings, | |
| .get_link = ethtool_op_get_link, | |
| .nway_reset = rtl8152_nway_reset, | |
| .get_msglevel = rtl8152_get_msglevel, | |
| .set_msglevel = rtl8152_set_msglevel, | |
| .get_wol = rtl8152_get_wol, | |
| .set_wol = rtl8152_set_wol, | |
| .get_strings = rtl8152_get_strings, | |
| .get_sset_count = rtl8152_get_sset_count, | |
| .get_ethtool_stats = rtl8152_get_ethtool_stats, | |
| .get_coalesce = rtl8152_get_coalesce, | |
| .set_coalesce = rtl8152_set_coalesce, | |
| .get_eee = rtl_ethtool_get_eee, | |
| .set_eee = rtl_ethtool_set_eee, | |
| }; | |
| static int rtl8152_ioctl(struct net_device *netdev, struct ifreq *rq, int cmd) | |
| { | |
| struct r8152 *tp = netdev_priv(netdev); | |
| struct mii_ioctl_data *data = if_mii(rq); | |
| int res; | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags)) | |
| return -ENODEV; | |
| res = usb_autopm_get_interface(tp->intf); | |
| if (res < 0) | |
| goto out; | |
| switch (cmd) { | |
| case SIOCGMIIPHY: | |
| data->phy_id = R8152_PHY_ID; /* Internal PHY */ | |
| break; | |
| case SIOCGMIIREG: | |
| mutex_lock(&tp->control); | |
| data->val_out = r8152_mdio_read(tp, data->reg_num); | |
| mutex_unlock(&tp->control); | |
| break; | |
| case SIOCSMIIREG: | |
| if (!capable(CAP_NET_ADMIN)) { | |
| res = -EPERM; | |
| break; | |
| } | |
| mutex_lock(&tp->control); | |
| r8152_mdio_write(tp, data->reg_num, data->val_in); | |
| mutex_unlock(&tp->control); | |
| break; | |
| default: | |
| res = -EOPNOTSUPP; | |
| } | |
| usb_autopm_put_interface(tp->intf); | |
| out: | |
| return res; | |
| } | |
| static int rtl8152_change_mtu(struct net_device *dev, int new_mtu) | |
| { | |
| struct r8152 *tp = netdev_priv(dev); | |
| int ret; | |
| switch (tp->version) { | |
| case RTL_VER_01: | |
| case RTL_VER_02: | |
| return eth_change_mtu(dev, new_mtu); | |
| default: | |
| break; | |
| } | |
| if (new_mtu < 68 || new_mtu > RTL8153_MAX_MTU) | |
| return -EINVAL; | |
| ret = usb_autopm_get_interface(tp->intf); | |
| if (ret < 0) | |
| return ret; | |
| mutex_lock(&tp->control); | |
| dev->mtu = new_mtu; | |
| if (netif_running(dev) && netif_carrier_ok(dev)) | |
| r8153_set_rx_early_size(tp); | |
| mutex_unlock(&tp->control); | |
| usb_autopm_put_interface(tp->intf); | |
| return ret; | |
| } | |
| static const struct net_device_ops rtl8152_netdev_ops = { | |
| .ndo_open = rtl8152_open, | |
| .ndo_stop = rtl8152_close, | |
| .ndo_do_ioctl = rtl8152_ioctl, | |
| .ndo_start_xmit = rtl8152_start_xmit, | |
| .ndo_tx_timeout = rtl8152_tx_timeout, | |
| .ndo_set_features = rtl8152_set_features, | |
| .ndo_set_rx_mode = rtl8152_set_rx_mode, | |
| .ndo_set_mac_address = rtl8152_set_mac_address, | |
| .ndo_change_mtu = rtl8152_change_mtu, | |
| .ndo_validate_addr = eth_validate_addr, | |
| .ndo_features_check = rtl8152_features_check, | |
| }; | |
| static void r8152b_get_version(struct r8152 *tp) | |
| { | |
| u32 ocp_data; | |
| u16 version; | |
| ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_TCR1); | |
| version = (u16)(ocp_data & VERSION_MASK); | |
| switch (version) { | |
| case 0x4c00: | |
| tp->version = RTL_VER_01; | |
| break; | |
| case 0x4c10: | |
| tp->version = RTL_VER_02; | |
| break; | |
| case 0x5c00: | |
| tp->version = RTL_VER_03; | |
| tp->mii.supports_gmii = 1; | |
| break; | |
| case 0x5c10: | |
| tp->version = RTL_VER_04; | |
| tp->mii.supports_gmii = 1; | |
| break; | |
| case 0x5c20: | |
| tp->version = RTL_VER_05; | |
| tp->mii.supports_gmii = 1; | |
| break; | |
| case 0x5c30: | |
| tp->version = RTL_VER_06; | |
| tp->mii.supports_gmii = 1; | |
| break; | |
| default: | |
| netif_info(tp, probe, tp->netdev, | |
| "Unknown version 0x%04x\n", version); | |
| break; | |
| } | |
| } | |
| static void rtl8152_unload(struct r8152 *tp) | |
| { | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags)) | |
| return; | |
| if (tp->version != RTL_VER_01) | |
| r8152_power_cut_en(tp, true); | |
| } | |
| static void rtl8153_unload(struct r8152 *tp) | |
| { | |
| if (test_bit(RTL8152_UNPLUG, &tp->flags)) | |
| return; | |
| r8153_power_cut_en(tp, false); | |
| } | |
| static int rtl_ops_init(struct r8152 *tp) | |
| { | |
| struct rtl_ops *ops = &tp->rtl_ops; | |
| int ret = 0; | |
| switch (tp->version) { | |
| case RTL_VER_01: | |
| case RTL_VER_02: | |
| ops->init = r8152b_init; | |
| ops->enable = rtl8152_enable; | |
| ops->disable = rtl8152_disable; | |
| ops->up = rtl8152_up; | |
| ops->down = rtl8152_down; | |
| ops->unload = rtl8152_unload; | |
| ops->eee_get = r8152_get_eee; | |
| ops->eee_set = r8152_set_eee; | |
| ops->in_nway = rtl8152_in_nway; | |
| break; | |
| case RTL_VER_03: | |
| case RTL_VER_04: | |
| case RTL_VER_05: | |
| case RTL_VER_06: | |
| ops->init = r8153_init; | |
| ops->enable = rtl8153_enable; | |
| ops->disable = rtl8153_disable; | |
| ops->up = rtl8153_up; | |
| ops->down = rtl8153_down; | |
| ops->unload = rtl8153_unload; | |
| ops->eee_get = r8153_get_eee; | |
| ops->eee_set = r8153_set_eee; | |
| ops->in_nway = rtl8153_in_nway; | |
| break; | |
| default: | |
| ret = -ENODEV; | |
| netif_err(tp, probe, tp->netdev, "Unknown Device\n"); | |
| break; | |
| } | |
| return ret; | |
| } | |
| static int rtl8152_probe(struct usb_interface *intf, | |
| const struct usb_device_id *id) | |
| { | |
| struct usb_device *udev = interface_to_usbdev(intf); | |
| struct r8152 *tp; | |
| struct net_device *netdev; | |
| int ret; | |
| if (udev->actconfig->desc.bConfigurationValue != 1) { | |
| usb_driver_set_configuration(udev, 1); | |
| return -ENODEV; | |
| } | |
| usb_reset_device(udev); | |
| netdev = alloc_etherdev(sizeof(struct r8152)); | |
| if (!netdev) { | |
| dev_err(&intf->dev, "Out of memory\n"); | |
| return -ENOMEM; | |
| } | |
| SET_NETDEV_DEV(netdev, &intf->dev); | |
| tp = netdev_priv(netdev); | |
| tp->msg_enable = 0x7FFF; | |
| tp->udev = udev; | |
| tp->netdev = netdev; | |
| tp->intf = intf; | |
| r8152b_get_version(tp); | |
| ret = rtl_ops_init(tp); | |
| if (ret) | |
| goto out; | |
| mutex_init(&tp->control); | |
| INIT_DELAYED_WORK(&tp->schedule, rtl_work_func_t); | |
| netdev->netdev_ops = &rtl8152_netdev_ops; | |
| netdev->watchdog_timeo = RTL8152_TX_TIMEOUT; | |
| netdev->features |= NETIF_F_RXCSUM | NETIF_F_IP_CSUM | NETIF_F_SG | | |
| NETIF_F_TSO | NETIF_F_FRAGLIST | NETIF_F_IPV6_CSUM | | |
| NETIF_F_TSO6 | NETIF_F_HW_VLAN_CTAG_RX | | |
| NETIF_F_HW_VLAN_CTAG_TX; | |
| netdev->hw_features = NETIF_F_RXCSUM | NETIF_F_IP_CSUM | NETIF_F_SG | | |
| NETIF_F_TSO | NETIF_F_FRAGLIST | | |
| NETIF_F_IPV6_CSUM | NETIF_F_TSO6 | | |
| NETIF_F_HW_VLAN_CTAG_RX | NETIF_F_HW_VLAN_CTAG_TX; | |
| netdev->vlan_features = NETIF_F_SG | NETIF_F_IP_CSUM | NETIF_F_TSO | | |
| NETIF_F_HIGHDMA | NETIF_F_FRAGLIST | | |
| NETIF_F_IPV6_CSUM | NETIF_F_TSO6; | |
| netdev->ethtool_ops = &ops; | |
| netif_set_gso_max_size(netdev, RTL_LIMITED_TSO_SIZE); | |
| tp->mii.dev = netdev; | |
| tp->mii.mdio_read = read_mii_word; | |
| tp->mii.mdio_write = write_mii_word; | |
| tp->mii.phy_id_mask = 0x3f; | |
| tp->mii.reg_num_mask = 0x1f; | |
| tp->mii.phy_id = R8152_PHY_ID; | |
| switch (udev->speed) { | |
| case USB_SPEED_SUPER: | |
| tp->coalesce = COALESCE_SUPER; | |
| break; | |
| case USB_SPEED_HIGH: | |
| tp->coalesce = COALESCE_HIGH; | |
| break; | |
| default: | |
| tp->coalesce = COALESCE_SLOW; | |
| break; | |
| } | |
| intf->needs_remote_wakeup = 1; | |
| tp->rtl_ops.init(tp); | |
| set_ethernet_addr(tp); | |
| usb_set_intfdata(intf, tp); | |
| netif_napi_add(netdev, &tp->napi, r8152_poll, RTL8152_NAPI_WEIGHT); | |
| ret = register_netdev(netdev); | |
| if (ret != 0) { | |
| netif_err(tp, probe, netdev, "couldn't register the device\n"); | |
| goto out1; | |
| } | |
| if (!rtl_can_wakeup(tp)) | |
| __rtl_set_wol(tp, 0); | |
| tp->saved_wolopts = __rtl_get_wol(tp); | |
| if (tp->saved_wolopts) | |
| device_set_wakeup_enable(&udev->dev, true); | |
| else | |
| device_set_wakeup_enable(&udev->dev, false); | |
| netif_info(tp, probe, netdev, "%s\n", DRIVER_VERSION); | |
| return 0; | |
| out1: | |
| netif_napi_del(&tp->napi); | |
| usb_set_intfdata(intf, NULL); | |
| out: | |
| free_netdev(netdev); | |
| return ret; | |
| } | |
| static void rtl8152_disconnect(struct usb_interface *intf) | |
| { | |
| struct r8152 *tp = usb_get_intfdata(intf); | |
| usb_set_intfdata(intf, NULL); | |
| if (tp) { | |
| struct usb_device *udev = tp->udev; | |
| if (udev->state == USB_STATE_NOTATTACHED) | |
| set_bit(RTL8152_UNPLUG, &tp->flags); | |
| netif_napi_del(&tp->napi); | |
| unregister_netdev(tp->netdev); | |
| tp->rtl_ops.unload(tp); | |
| free_netdev(tp->netdev); | |
| } | |
| } | |
| #define REALTEK_USB_DEVICE(vend, prod) \ | |
| .match_flags = USB_DEVICE_ID_MATCH_DEVICE | \ | |
| USB_DEVICE_ID_MATCH_INT_CLASS, \ | |
| .idVendor = (vend), \ | |
| .idProduct = (prod), \ | |
| .bInterfaceClass = USB_CLASS_VENDOR_SPEC \ | |
| }, \ | |
| { \ | |
| .match_flags = USB_DEVICE_ID_MATCH_INT_INFO | \ | |
| USB_DEVICE_ID_MATCH_DEVICE, \ | |
| .idVendor = (vend), \ | |
| .idProduct = (prod), \ | |
| .bInterfaceClass = USB_CLASS_COMM, \ | |
| .bInterfaceSubClass = USB_CDC_SUBCLASS_ETHERNET, \ | |
| .bInterfaceProtocol = USB_CDC_PROTO_NONE | |
| /* table of devices that work with this driver */ | |
| static struct usb_device_id rtl8152_table[] = { | |
| {REALTEK_USB_DEVICE(VENDOR_ID_REALTEK, 0x8152)}, | |
| {REALTEK_USB_DEVICE(VENDOR_ID_REALTEK, 0x8153)}, | |
| {REALTEK_USB_DEVICE(VENDOR_ID_SAMSUNG, 0xa101)}, | |
| {REALTEK_USB_DEVICE(VENDOR_ID_LENOVO, 0x7205)}, | |
| {REALTEK_USB_DEVICE(VENDOR_ID_LENOVO, 0x304f)}, | |
| {REALTEK_USB_DEVICE(VENDOR_ID_NVIDIA, 0x09ff)}, | |
| {} | |
| }; | |
| MODULE_DEVICE_TABLE(usb, rtl8152_table); | |
| static struct usb_driver rtl8152_driver = { | |
| .name = MODULENAME, | |
| .id_table = rtl8152_table, | |
| .probe = rtl8152_probe, | |
| .disconnect = rtl8152_disconnect, | |
| .suspend = rtl8152_suspend, | |
| .resume = rtl8152_resume, | |
| .reset_resume = rtl8152_reset_resume, | |
| .pre_reset = rtl8152_pre_reset, | |
| .post_reset = rtl8152_post_reset, | |
| .supports_autosuspend = 1, | |
| .disable_hub_initiated_lpm = 1, | |
| }; | |
| module_usb_driver(rtl8152_driver); | |
| MODULE_AUTHOR(DRIVER_AUTHOR); | |
| MODULE_DESCRIPTION(DRIVER_DESC); | |
| MODULE_LICENSE("GPL"); |