| /* | |
| * Copyright (C) 2002 Intersil Americas Inc. | |
| * Copyright (C) 2004 Aurelien Alleaume <slts@free.fr> | |
| * This program is free software; you can redistribute it and/or modify | |
| * it under the terms of the GNU General Public License as published by | |
| * the Free Software Foundation; either version 2 of the License | |
| * | |
| * This program is distributed in the hope that it will be useful, | |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of | |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
| * GNU General Public License for more details. | |
| * | |
| * You should have received a copy of the GNU General Public License | |
| * along with this program; if not, see <http://www.gnu.org/licenses/>. | |
| * | |
| */ | |
| #include <linux/module.h> | |
| #include <linux/gfp.h> | |
| #include <linux/pci.h> | |
| #include <linux/delay.h> | |
| #include <linux/netdevice.h> | |
| #include <linux/etherdevice.h> | |
| #include <linux/if_arp.h> | |
| #include <asm/byteorder.h> | |
| #include "prismcompat.h" | |
| #include "isl_38xx.h" | |
| #include "islpci_eth.h" | |
| #include "islpci_mgt.h" | |
| #include "oid_mgt.h" | |
| /****************************************************************************** | |
| Network Interface functions | |
| ******************************************************************************/ | |
| void | |
| islpci_eth_cleanup_transmit(islpci_private *priv, | |
| isl38xx_control_block *control_block) | |
| { | |
| struct sk_buff *skb; | |
| u32 index; | |
| /* compare the control block read pointer with the free pointer */ | |
| while (priv->free_data_tx != | |
| le32_to_cpu(control_block-> | |
| device_curr_frag[ISL38XX_CB_TX_DATA_LQ])) { | |
| /* read the index of the first fragment to be freed */ | |
| index = priv->free_data_tx % ISL38XX_CB_TX_QSIZE; | |
| /* check for holes in the arrays caused by multi fragment frames | |
| * searching for the last fragment of a frame */ | |
| if (priv->pci_map_tx_address[index]) { | |
| /* entry is the last fragment of a frame | |
| * free the skb structure and unmap pci memory */ | |
| skb = priv->data_low_tx[index]; | |
| #if VERBOSE > SHOW_ERROR_MESSAGES | |
| DEBUG(SHOW_TRACING, | |
| "cleanup skb %p skb->data %p skb->len %u truesize %u\n ", | |
| skb, skb->data, skb->len, skb->truesize); | |
| #endif | |
| pci_unmap_single(priv->pdev, | |
| priv->pci_map_tx_address[index], | |
| skb->len, PCI_DMA_TODEVICE); | |
| dev_kfree_skb_irq(skb); | |
| skb = NULL; | |
| } | |
| /* increment the free data low queue pointer */ | |
| priv->free_data_tx++; | |
| } | |
| } | |
| netdev_tx_t | |
| islpci_eth_transmit(struct sk_buff *skb, struct net_device *ndev) | |
| { | |
| islpci_private *priv = netdev_priv(ndev); | |
| isl38xx_control_block *cb = priv->control_block; | |
| u32 index; | |
| dma_addr_t pci_map_address; | |
| int frame_size; | |
| isl38xx_fragment *fragment; | |
| int offset; | |
| struct sk_buff *newskb; | |
| int newskb_offset; | |
| unsigned long flags; | |
| unsigned char wds_mac[6]; | |
| u32 curr_frag; | |
| #if VERBOSE > SHOW_ERROR_MESSAGES | |
| DEBUG(SHOW_FUNCTION_CALLS, "islpci_eth_transmit\n"); | |
| #endif | |
| /* lock the driver code */ | |
| spin_lock_irqsave(&priv->slock, flags); | |
| /* check whether the destination queue has enough fragments for the frame */ | |
| curr_frag = le32_to_cpu(cb->driver_curr_frag[ISL38XX_CB_TX_DATA_LQ]); | |
| if (unlikely(curr_frag - priv->free_data_tx >= ISL38XX_CB_TX_QSIZE)) { | |
| printk(KERN_ERR "%s: transmit device queue full when awake\n", | |
| ndev->name); | |
| netif_stop_queue(ndev); | |
| /* trigger the device */ | |
| isl38xx_w32_flush(priv->device_base, ISL38XX_DEV_INT_UPDATE, | |
| ISL38XX_DEV_INT_REG); | |
| udelay(ISL38XX_WRITEIO_DELAY); | |
| goto drop_free; | |
| } | |
| /* Check alignment and WDS frame formatting. The start of the packet should | |
| * be aligned on a 4-byte boundary. If WDS is enabled add another 6 bytes | |
| * and add WDS address information */ | |
| if (likely(((long) skb->data & 0x03) | init_wds)) { | |
| /* get the number of bytes to add and re-align */ | |
| offset = (4 - (long) skb->data) & 0x03; | |
| offset += init_wds ? 6 : 0; | |
| /* check whether the current skb can be used */ | |
| if (!skb_cloned(skb) && (skb_tailroom(skb) >= offset)) { | |
| unsigned char *src = skb->data; | |
| #if VERBOSE > SHOW_ERROR_MESSAGES | |
| DEBUG(SHOW_TRACING, "skb offset %i wds %i\n", offset, | |
| init_wds); | |
| #endif | |
| /* align the buffer on 4-byte boundary */ | |
| skb_reserve(skb, (4 - (long) skb->data) & 0x03); | |
| if (init_wds) { | |
| /* wds requires an additional address field of 6 bytes */ | |
| skb_put(skb, 6); | |
| #ifdef ISLPCI_ETH_DEBUG | |
| printk("islpci_eth_transmit:wds_mac\n"); | |
| #endif | |
| memmove(skb->data + 6, src, skb->len); | |
| skb_copy_to_linear_data(skb, wds_mac, 6); | |
| } else { | |
| memmove(skb->data, src, skb->len); | |
| } | |
| #if VERBOSE > SHOW_ERROR_MESSAGES | |
| DEBUG(SHOW_TRACING, "memmove %p %p %i\n", skb->data, | |
| src, skb->len); | |
| #endif | |
| } else { | |
| newskb = | |
| dev_alloc_skb(init_wds ? skb->len + 6 : skb->len); | |
| if (unlikely(newskb == NULL)) { | |
| printk(KERN_ERR "%s: Cannot allocate skb\n", | |
| ndev->name); | |
| goto drop_free; | |
| } | |
| newskb_offset = (4 - (long) newskb->data) & 0x03; | |
| /* Check if newskb->data is aligned */ | |
| if (newskb_offset) | |
| skb_reserve(newskb, newskb_offset); | |
| skb_put(newskb, init_wds ? skb->len + 6 : skb->len); | |
| if (init_wds) { | |
| skb_copy_from_linear_data(skb, | |
| newskb->data + 6, | |
| skb->len); | |
| skb_copy_to_linear_data(newskb, wds_mac, 6); | |
| #ifdef ISLPCI_ETH_DEBUG | |
| printk("islpci_eth_transmit:wds_mac\n"); | |
| #endif | |
| } else | |
| skb_copy_from_linear_data(skb, newskb->data, | |
| skb->len); | |
| #if VERBOSE > SHOW_ERROR_MESSAGES | |
| DEBUG(SHOW_TRACING, "memcpy %p %p %i wds %i\n", | |
| newskb->data, skb->data, skb->len, init_wds); | |
| #endif | |
| newskb->dev = skb->dev; | |
| dev_kfree_skb_irq(skb); | |
| skb = newskb; | |
| } | |
| } | |
| /* display the buffer contents for debugging */ | |
| #if VERBOSE > SHOW_ERROR_MESSAGES | |
| DEBUG(SHOW_BUFFER_CONTENTS, "\ntx %p ", skb->data); | |
| display_buffer((char *) skb->data, skb->len); | |
| #endif | |
| /* map the skb buffer to pci memory for DMA operation */ | |
| pci_map_address = pci_map_single(priv->pdev, | |
| (void *) skb->data, skb->len, | |
| PCI_DMA_TODEVICE); | |
| if (unlikely(pci_map_address == 0)) { | |
| printk(KERN_WARNING "%s: cannot map buffer to PCI\n", | |
| ndev->name); | |
| goto drop_free; | |
| } | |
| /* Place the fragment in the control block structure. */ | |
| index = curr_frag % ISL38XX_CB_TX_QSIZE; | |
| fragment = &cb->tx_data_low[index]; | |
| priv->pci_map_tx_address[index] = pci_map_address; | |
| /* store the skb address for future freeing */ | |
| priv->data_low_tx[index] = skb; | |
| /* set the proper fragment start address and size information */ | |
| frame_size = skb->len; | |
| fragment->size = cpu_to_le16(frame_size); | |
| fragment->flags = cpu_to_le16(0); /* set to 1 if more fragments */ | |
| fragment->address = cpu_to_le32(pci_map_address); | |
| curr_frag++; | |
| /* The fragment address in the control block must have been | |
| * written before announcing the frame buffer to device. */ | |
| wmb(); | |
| cb->driver_curr_frag[ISL38XX_CB_TX_DATA_LQ] = cpu_to_le32(curr_frag); | |
| if (curr_frag - priv->free_data_tx + ISL38XX_MIN_QTHRESHOLD | |
| > ISL38XX_CB_TX_QSIZE) { | |
| /* stop sends from upper layers */ | |
| netif_stop_queue(ndev); | |
| /* set the full flag for the transmission queue */ | |
| priv->data_low_tx_full = 1; | |
| } | |
| ndev->stats.tx_packets++; | |
| ndev->stats.tx_bytes += skb->len; | |
| /* trigger the device */ | |
| islpci_trigger(priv); | |
| /* unlock the driver code */ | |
| spin_unlock_irqrestore(&priv->slock, flags); | |
| return NETDEV_TX_OK; | |
| drop_free: | |
| ndev->stats.tx_dropped++; | |
| spin_unlock_irqrestore(&priv->slock, flags); | |
| dev_kfree_skb(skb); | |
| return NETDEV_TX_OK; | |
| } | |
| static inline int | |
| islpci_monitor_rx(islpci_private *priv, struct sk_buff **skb) | |
| { | |
| /* The card reports full 802.11 packets but with a 20 bytes | |
| * header and without the FCS. But there a is a bit that | |
| * indicates if the packet is corrupted :-) */ | |
| struct rfmon_header *hdr = (struct rfmon_header *) (*skb)->data; | |
| if (hdr->flags & 0x01) | |
| /* This one is bad. Drop it ! */ | |
| return -1; | |
| if (priv->ndev->type == ARPHRD_IEEE80211_PRISM) { | |
| struct avs_80211_1_header *avs; | |
| /* extract the relevant data from the header */ | |
| u32 clock = le32_to_cpu(hdr->clock); | |
| u8 rate = hdr->rate; | |
| u16 freq = le16_to_cpu(hdr->freq); | |
| u8 rssi = hdr->rssi; | |
| skb_pull(*skb, sizeof (struct rfmon_header)); | |
| if (skb_headroom(*skb) < sizeof (struct avs_80211_1_header)) { | |
| struct sk_buff *newskb = skb_copy_expand(*skb, | |
| sizeof (struct | |
| avs_80211_1_header), | |
| 0, GFP_ATOMIC); | |
| if (newskb) { | |
| dev_kfree_skb_irq(*skb); | |
| *skb = newskb; | |
| } else | |
| return -1; | |
| /* This behavior is not very subtile... */ | |
| } | |
| /* make room for the new header and fill it. */ | |
| avs = | |
| (struct avs_80211_1_header *) skb_push(*skb, | |
| sizeof (struct | |
| avs_80211_1_header)); | |
| avs->version = cpu_to_be32(P80211CAPTURE_VERSION); | |
| avs->length = cpu_to_be32(sizeof (struct avs_80211_1_header)); | |
| avs->mactime = cpu_to_be64(clock); | |
| avs->hosttime = cpu_to_be64(jiffies); | |
| avs->phytype = cpu_to_be32(6); /*OFDM: 6 for (g), 8 for (a) */ | |
| avs->channel = cpu_to_be32(channel_of_freq(freq)); | |
| avs->datarate = cpu_to_be32(rate * 5); | |
| avs->antenna = cpu_to_be32(0); /*unknown */ | |
| avs->priority = cpu_to_be32(0); /*unknown */ | |
| avs->ssi_type = cpu_to_be32(3); /*2: dBm, 3: raw RSSI */ | |
| avs->ssi_signal = cpu_to_be32(rssi & 0x7f); | |
| avs->ssi_noise = cpu_to_be32(priv->local_iwstatistics.qual.noise); /*better than 'undefined', I assume */ | |
| avs->preamble = cpu_to_be32(0); /*unknown */ | |
| avs->encoding = cpu_to_be32(0); /*unknown */ | |
| } else | |
| skb_pull(*skb, sizeof (struct rfmon_header)); | |
| (*skb)->protocol = htons(ETH_P_802_2); | |
| skb_reset_mac_header(*skb); | |
| (*skb)->pkt_type = PACKET_OTHERHOST; | |
| return 0; | |
| } | |
| int | |
| islpci_eth_receive(islpci_private *priv) | |
| { | |
| struct net_device *ndev = priv->ndev; | |
| isl38xx_control_block *control_block = priv->control_block; | |
| struct sk_buff *skb; | |
| u16 size; | |
| u32 index, offset; | |
| unsigned char *src; | |
| int discard = 0; | |
| #if VERBOSE > SHOW_ERROR_MESSAGES | |
| DEBUG(SHOW_FUNCTION_CALLS, "islpci_eth_receive\n"); | |
| #endif | |
| /* the device has written an Ethernet frame in the data area | |
| * of the sk_buff without updating the structure, do it now */ | |
| index = priv->free_data_rx % ISL38XX_CB_RX_QSIZE; | |
| size = le16_to_cpu(control_block->rx_data_low[index].size); | |
| skb = priv->data_low_rx[index]; | |
| offset = ((unsigned long) | |
| le32_to_cpu(control_block->rx_data_low[index].address) - | |
| (unsigned long) skb->data) & 3; | |
| #if VERBOSE > SHOW_ERROR_MESSAGES | |
| DEBUG(SHOW_TRACING, | |
| "frq->addr %x skb->data %p skb->len %u offset %u truesize %u\n ", | |
| control_block->rx_data_low[priv->free_data_rx].address, skb->data, | |
| skb->len, offset, skb->truesize); | |
| #endif | |
| /* delete the streaming DMA mapping before processing the skb */ | |
| pci_unmap_single(priv->pdev, | |
| priv->pci_map_rx_address[index], | |
| MAX_FRAGMENT_SIZE_RX + 2, PCI_DMA_FROMDEVICE); | |
| /* update the skb structure and align the buffer */ | |
| skb_put(skb, size); | |
| if (offset) { | |
| /* shift the buffer allocation offset bytes to get the right frame */ | |
| skb_pull(skb, 2); | |
| skb_put(skb, 2); | |
| } | |
| #if VERBOSE > SHOW_ERROR_MESSAGES | |
| /* display the buffer contents for debugging */ | |
| DEBUG(SHOW_BUFFER_CONTENTS, "\nrx %p ", skb->data); | |
| display_buffer((char *) skb->data, skb->len); | |
| #endif | |
| /* check whether WDS is enabled and whether the data frame is a WDS frame */ | |
| if (init_wds) { | |
| /* WDS enabled, check for the wds address on the first 6 bytes of the buffer */ | |
| src = skb->data + 6; | |
| memmove(skb->data, src, skb->len - 6); | |
| skb_trim(skb, skb->len - 6); | |
| } | |
| #if VERBOSE > SHOW_ERROR_MESSAGES | |
| DEBUG(SHOW_TRACING, "Fragment size %i in skb at %p\n", size, skb); | |
| DEBUG(SHOW_TRACING, "Skb data at %p, length %i\n", skb->data, skb->len); | |
| /* display the buffer contents for debugging */ | |
| DEBUG(SHOW_BUFFER_CONTENTS, "\nrx %p ", skb->data); | |
| display_buffer((char *) skb->data, skb->len); | |
| #endif | |
| /* take care of monitor mode and spy monitoring. */ | |
| if (unlikely(priv->iw_mode == IW_MODE_MONITOR)) { | |
| skb->dev = ndev; | |
| discard = islpci_monitor_rx(priv, &skb); | |
| } else { | |
| if (unlikely(skb->data[2 * ETH_ALEN] == 0)) { | |
| /* The packet has a rx_annex. Read it for spy monitoring, Then | |
| * remove it, while keeping the 2 leading MAC addr. | |
| */ | |
| struct iw_quality wstats; | |
| struct rx_annex_header *annex = | |
| (struct rx_annex_header *) skb->data; | |
| wstats.level = annex->rfmon.rssi; | |
| /* The noise value can be a bit outdated if nobody's | |
| * reading wireless stats... */ | |
| wstats.noise = priv->local_iwstatistics.qual.noise; | |
| wstats.qual = wstats.level - wstats.noise; | |
| wstats.updated = 0x07; | |
| /* Update spy records */ | |
| wireless_spy_update(ndev, annex->addr2, &wstats); | |
| skb_copy_from_linear_data(skb, | |
| (skb->data + | |
| sizeof(struct rfmon_header)), | |
| 2 * ETH_ALEN); | |
| skb_pull(skb, sizeof (struct rfmon_header)); | |
| } | |
| skb->protocol = eth_type_trans(skb, ndev); | |
| } | |
| skb->ip_summed = CHECKSUM_NONE; | |
| ndev->stats.rx_packets++; | |
| ndev->stats.rx_bytes += size; | |
| /* deliver the skb to the network layer */ | |
| #ifdef ISLPCI_ETH_DEBUG | |
| printk | |
| ("islpci_eth_receive:netif_rx %2.2X %2.2X %2.2X %2.2X %2.2X %2.2X\n", | |
| skb->data[0], skb->data[1], skb->data[2], skb->data[3], | |
| skb->data[4], skb->data[5]); | |
| #endif | |
| if (unlikely(discard)) { | |
| dev_kfree_skb_irq(skb); | |
| skb = NULL; | |
| } else | |
| netif_rx(skb); | |
| /* increment the read index for the rx data low queue */ | |
| priv->free_data_rx++; | |
| /* add one or more sk_buff structures */ | |
| while (index = | |
| le32_to_cpu(control_block-> | |
| driver_curr_frag[ISL38XX_CB_RX_DATA_LQ]), | |
| index - priv->free_data_rx < ISL38XX_CB_RX_QSIZE) { | |
| /* allocate an sk_buff for received data frames storage | |
| * include any required allignment operations */ | |
| skb = dev_alloc_skb(MAX_FRAGMENT_SIZE_RX + 2); | |
| if (unlikely(skb == NULL)) { | |
| /* error allocating an sk_buff structure elements */ | |
| DEBUG(SHOW_ERROR_MESSAGES, "Error allocating skb\n"); | |
| break; | |
| } | |
| skb_reserve(skb, (4 - (long) skb->data) & 0x03); | |
| /* store the new skb structure pointer */ | |
| index = index % ISL38XX_CB_RX_QSIZE; | |
| priv->data_low_rx[index] = skb; | |
| #if VERBOSE > SHOW_ERROR_MESSAGES | |
| DEBUG(SHOW_TRACING, | |
| "new alloc skb %p skb->data %p skb->len %u index %u truesize %u\n ", | |
| skb, skb->data, skb->len, index, skb->truesize); | |
| #endif | |
| /* set the streaming DMA mapping for proper PCI bus operation */ | |
| priv->pci_map_rx_address[index] = | |
| pci_map_single(priv->pdev, (void *) skb->data, | |
| MAX_FRAGMENT_SIZE_RX + 2, | |
| PCI_DMA_FROMDEVICE); | |
| if (unlikely(!priv->pci_map_rx_address[index])) { | |
| /* error mapping the buffer to device accessible memory address */ | |
| DEBUG(SHOW_ERROR_MESSAGES, | |
| "Error mapping DMA address\n"); | |
| /* free the skbuf structure before aborting */ | |
| dev_kfree_skb_irq(skb); | |
| skb = NULL; | |
| break; | |
| } | |
| /* update the fragment address */ | |
| control_block->rx_data_low[index].address = | |
| cpu_to_le32((u32)priv->pci_map_rx_address[index]); | |
| wmb(); | |
| /* increment the driver read pointer */ | |
| le32_add_cpu(&control_block-> | |
| driver_curr_frag[ISL38XX_CB_RX_DATA_LQ], 1); | |
| } | |
| /* trigger the device */ | |
| islpci_trigger(priv); | |
| return 0; | |
| } | |
| void | |
| islpci_do_reset_and_wake(struct work_struct *work) | |
| { | |
| islpci_private *priv = container_of(work, islpci_private, reset_task); | |
| islpci_reset(priv, 1); | |
| priv->reset_task_pending = 0; | |
| smp_wmb(); | |
| netif_wake_queue(priv->ndev); | |
| } | |
| void | |
| islpci_eth_tx_timeout(struct net_device *ndev) | |
| { | |
| islpci_private *priv = netdev_priv(ndev); | |
| /* increment the transmit error counter */ | |
| ndev->stats.tx_errors++; | |
| if (!priv->reset_task_pending) { | |
| printk(KERN_WARNING | |
| "%s: tx_timeout, scheduling reset", ndev->name); | |
| netif_stop_queue(ndev); | |
| priv->reset_task_pending = 1; | |
| schedule_work(&priv->reset_task); | |
| } else { | |
| printk(KERN_WARNING | |
| "%s: tx_timeout, waiting for reset", ndev->name); | |
| } | |
| } |