| Kernel driver zl6100 | |
| ==================== | |
| Supported chips: | |
| * Intersil / Zilker Labs ZL2004 | |
| Prefix: 'zl2004' | |
| Addresses scanned: - | |
| Datasheet: http://www.intersil.com/data/fn/fn6847.pdf | |
| * Intersil / Zilker Labs ZL2005 | |
| Prefix: 'zl2005' | |
| Addresses scanned: - | |
| Datasheet: http://www.intersil.com/data/fn/fn6848.pdf | |
| * Intersil / Zilker Labs ZL2006 | |
| Prefix: 'zl2006' | |
| Addresses scanned: - | |
| Datasheet: http://www.intersil.com/data/fn/fn6850.pdf | |
| * Intersil / Zilker Labs ZL2008 | |
| Prefix: 'zl2008' | |
| Addresses scanned: - | |
| Datasheet: http://www.intersil.com/data/fn/fn6859.pdf | |
| * Intersil / Zilker Labs ZL2105 | |
| Prefix: 'zl2105' | |
| Addresses scanned: - | |
| Datasheet: http://www.intersil.com/data/fn/fn6851.pdf | |
| * Intersil / Zilker Labs ZL2106 | |
| Prefix: 'zl2106' | |
| Addresses scanned: - | |
| Datasheet: http://www.intersil.com/data/fn/fn6852.pdf | |
| * Intersil / Zilker Labs ZL6100 | |
| Prefix: 'zl6100' | |
| Addresses scanned: - | |
| Datasheet: http://www.intersil.com/data/fn/fn6876.pdf | |
| * Intersil / Zilker Labs ZL6105 | |
| Prefix: 'zl6105' | |
| Addresses scanned: - | |
| Datasheet: http://www.intersil.com/data/fn/fn6906.pdf | |
| * Intersil / Zilker Labs ZL9101M | |
| Prefix: 'zl9101' | |
| Addresses scanned: - | |
| Datasheet: http://www.intersil.com/data/fn/fn7669.pdf | |
| * Intersil / Zilker Labs ZL9117M | |
| Prefix: 'zl9117' | |
| Addresses scanned: - | |
| Datasheet: http://www.intersil.com/data/fn/fn7914.pdf | |
| * Ericsson BMR450, BMR451 | |
| Prefix: 'bmr450', 'bmr451' | |
| Addresses scanned: - | |
| Datasheet: | |
| http://archive.ericsson.net/service/internet/picov/get?DocNo=28701-EN/LZT146401 | |
| * Ericsson BMR462, BMR463, BMR464 | |
| Prefixes: 'bmr462', 'bmr463', 'bmr464' | |
| Addresses scanned: - | |
| Datasheet: | |
| http://archive.ericsson.net/service/internet/picov/get?DocNo=28701-EN/LZT146256 | |
| Author: Guenter Roeck <linux@roeck-us.net> | |
| Description | |
| ----------- | |
| This driver supports hardware monitoring for Intersil / Zilker Labs ZL6100 and | |
| compatible digital DC-DC controllers. | |
| The driver is a client driver to the core PMBus driver. Please see | |
| Documentation/hwmon/pmbus and Documentation.hwmon/pmbus-core for details | |
| on PMBus client drivers. | |
| Usage Notes | |
| ----------- | |
| This driver does not auto-detect devices. You will have to instantiate the | |
| devices explicitly. Please see Documentation/i2c/instantiating-devices for | |
| details. | |
| WARNING: Do not access chip registers using the i2cdump command, and do not use | |
| any of the i2ctools commands on a command register used to save and restore | |
| configuration data (0x11, 0x12, 0x15, 0x16, and 0xf4). The chips supported by | |
| this driver interpret any access to those command registers (including read | |
| commands) as request to execute the command in question. Unless write accesses | |
| to those registers are protected, this may result in power loss, board resets, | |
| and/or Flash corruption. Worst case, your board may turn into a brick. | |
| Platform data support | |
| --------------------- | |
| The driver supports standard PMBus driver platform data. | |
| Module parameters | |
| ----------------- | |
| delay | |
| ----- | |
| Intersil/Zilker Labs DC-DC controllers require a minimum interval between I2C | |
| bus accesses. According to Intersil, the minimum interval is 2 ms, though 1 ms | |
| appears to be sufficient and has not caused any problems in testing. The problem | |
| is known to affect all currently supported chips. For manual override, the | |
| driver provides a writeable module parameter, 'delay', which can be used to set | |
| the interval to a value between 0 and 65,535 microseconds. | |
| Sysfs entries | |
| ------------- | |
| The following attributes are supported. Limits are read-write; all other | |
| attributes are read-only. | |
| in1_label "vin" | |
| in1_input Measured input voltage. | |
| in1_min Minimum input voltage. | |
| in1_max Maximum input voltage. | |
| in1_lcrit Critical minimum input voltage. | |
| in1_crit Critical maximum input voltage. | |
| in1_min_alarm Input voltage low alarm. | |
| in1_max_alarm Input voltage high alarm. | |
| in1_lcrit_alarm Input voltage critical low alarm. | |
| in1_crit_alarm Input voltage critical high alarm. | |
| in2_label "vmon" | |
| in2_input Measured voltage on VMON (ZL2004) or VDRV (ZL9101M, | |
| ZL9117M) pin. Reported voltage is 16x the voltage on the | |
| pin (adjusted internally by the chip). | |
| in2_lcrit Critical minimum VMON/VDRV Voltage. | |
| in2_crit Critical maximum VMON/VDRV voltage. | |
| in2_lcrit_alarm VMON/VDRV voltage critical low alarm. | |
| in2_crit_alarm VMON/VDRV voltage critical high alarm. | |
| vmon attributes are supported on ZL2004, ZL9101M, | |
| and ZL9117M only. | |
| inX_label "vout1" | |
| inX_input Measured output voltage. | |
| inX_lcrit Critical minimum output Voltage. | |
| inX_crit Critical maximum output voltage. | |
| inX_lcrit_alarm Critical output voltage critical low alarm. | |
| inX_crit_alarm Critical output voltage critical high alarm. | |
| X is 3 for ZL2004, ZL9101M, and ZL9117M, 2 otherwise. | |
| curr1_label "iout1" | |
| curr1_input Measured output current. | |
| curr1_lcrit Critical minimum output current. | |
| curr1_crit Critical maximum output current. | |
| curr1_lcrit_alarm Output current critical low alarm. | |
| curr1_crit_alarm Output current critical high alarm. | |
| temp[12]_input Measured temperature. | |
| temp[12]_min Minimum temperature. | |
| temp[12]_max Maximum temperature. | |
| temp[12]_lcrit Critical low temperature. | |
| temp[12]_crit Critical high temperature. | |
| temp[12]_min_alarm Chip temperature low alarm. | |
| temp[12]_max_alarm Chip temperature high alarm. | |
| temp[12]_lcrit_alarm Chip temperature critical low alarm. | |
| temp[12]_crit_alarm Chip temperature critical high alarm. |