| /* |
| * Copyright (c) 2013 ARM Limited |
| * All rights reserved |
| * |
| * The license below extends only to copyright in the software and shall |
| * not be construed as granting a license to any other intellectual |
| * property including but not limited to intellectual property relating |
| * to a hardware implementation of the functionality of the software |
| * licensed hereunder. You may use the software subject to the license |
| * terms below provided that you ensure that this notice is replicated |
| * unmodified and in its entirety in all distributions of the software, |
| * modified or unmodified, in source code or in binary form. |
| * |
| * Copyright (c) 2004-2005 The Regents of The University of Michigan |
| * All rights reserved. |
| * |
| * Redistribution and use in source and binary forms, with or without |
| * modification, are permitted provided that the following conditions are |
| * met: redistributions of source code must retain the above copyright |
| * notice, this list of conditions and the following disclaimer; |
| * redistributions in binary form must reproduce the above copyright |
| * notice, this list of conditions and the following disclaimer in the |
| * documentation and/or other materials provided with the distribution; |
| * neither the name of the copyright holders nor the names of its |
| * contributors may be used to endorse or promote products derived from |
| * this software without specific prior written permission. |
| * |
| * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS |
| * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT |
| * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR |
| * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT |
| * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, |
| * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT |
| * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, |
| * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY |
| * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT |
| * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE |
| * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |
| */ |
| |
| /** @file |
| * Device model implementation for an IDE disk |
| */ |
| |
| #include "dev/storage/ide_disk.hh" |
| |
| #include <cerrno> |
| #include <cstring> |
| #include <deque> |
| #include <string> |
| |
| #include "base/chunk_generator.hh" |
| #include "base/cprintf.hh" // csprintf |
| #include "base/trace.hh" |
| #include "debug/IdeDisk.hh" |
| #include "dev/storage/disk_image.hh" |
| #include "dev/storage/ide_ctrl.hh" |
| #include "sim/core.hh" |
| #include "sim/sim_object.hh" |
| |
| IdeDisk::IdeDisk(const Params &p) |
| : SimObject(p), ctrl(NULL), image(p.image), diskDelay(p.delay), |
| ideDiskStats(this), |
| dmaTransferEvent([this]{ doDmaTransfer(); }, name()), |
| dmaReadCG(NULL), |
| dmaReadWaitEvent([this]{ doDmaRead(); }, name()), |
| dmaWriteCG(NULL), |
| dmaWriteWaitEvent([this]{ doDmaWrite(); }, name()), |
| dmaPrdReadEvent([this]{ dmaPrdReadDone(); }, name()), |
| dmaReadEvent([this]{ dmaReadDone(); }, name()), |
| dmaWriteEvent([this]{ dmaWriteDone(); }, name()) |
| { |
| // Reset the device state |
| reset(p.driveID); |
| |
| // fill out the drive ID structure |
| memset(&driveID, 0, sizeof(struct ataparams)); |
| |
| // Calculate LBA and C/H/S values |
| uint16_t cylinders; |
| uint8_t heads; |
| uint8_t sectors; |
| |
| uint32_t lba_size = image->size(); |
| if (lba_size >= 16383*16*63) { |
| cylinders = 16383; |
| heads = 16; |
| sectors = 63; |
| } else { |
| if (lba_size >= 63) |
| sectors = 63; |
| else if (lba_size == 0) |
| panic("Bad IDE image size: 0\n"); |
| else |
| sectors = lba_size; |
| |
| if ((lba_size / sectors) >= 16) |
| heads = 16; |
| else |
| heads = (lba_size / sectors); |
| |
| cylinders = lba_size / (heads * sectors); |
| } |
| |
| // Setup the model name |
| strncpy((char *)driveID.atap_model, "5MI EDD si k", |
| sizeof(driveID.atap_model)); |
| // Set the maximum multisector transfer size |
| driveID.atap_multi = MAX_MULTSECT; |
| // IORDY supported, IORDY disabled, LBA enabled, DMA enabled |
| driveID.atap_capabilities1 = 0x7; |
| // UDMA support, EIDE support |
| driveID.atap_extensions = 0x6; |
| // Setup default C/H/S settings |
| driveID.atap_cylinders = cylinders; |
| driveID.atap_sectors = sectors; |
| driveID.atap_heads = heads; |
| // Setup the current multisector transfer size |
| driveID.atap_curmulti = MAX_MULTSECT; |
| driveID.atap_curmulti_valid = 0x1; |
| // Number of sectors on disk |
| driveID.atap_capacity = lba_size; |
| // Multiword DMA mode 2 and below supported |
| driveID.atap_dmamode_supp = 0x4; |
| // Set PIO mode 4 and 3 supported |
| driveID.atap_piomode_supp = 0x3; |
| // Set DMA mode 4 and below supported |
| driveID.atap_udmamode_supp = 0x1f; |
| // Statically set hardware config word |
| driveID.atap_hwreset_res = 0x4001; |
| |
| //arbitrary for now... |
| driveID.atap_ata_major = WDC_VER_ATA7; |
| } |
| |
| IdeDisk::~IdeDisk() |
| { |
| // destroy the data buffer |
| delete [] dataBuffer; |
| } |
| |
| void |
| IdeDisk::reset(int id) |
| { |
| // initialize the data buffer and shadow registers |
| dataBuffer = new uint8_t[MAX_DMA_SIZE]; |
| |
| memset(dataBuffer, 0, MAX_DMA_SIZE); |
| memset(&cmdReg, 0, sizeof(CommandReg_t)); |
| memset(&curPrd.entry, 0, sizeof(PrdEntry_t)); |
| |
| curPrdAddr = 0; |
| curSector = 0; |
| cmdBytes = 0; |
| cmdBytesLeft = 0; |
| drqBytesLeft = 0; |
| dmaRead = false; |
| intrPending = false; |
| dmaAborted = false; |
| |
| // set the device state to idle |
| dmaState = Dma_Idle; |
| |
| if (id == DEV0) { |
| devState = Device_Idle_S; |
| devID = DEV0; |
| } else if (id == DEV1) { |
| devState = Device_Idle_NS; |
| devID = DEV1; |
| } else { |
| panic("Invalid device ID: %#x\n", id); |
| } |
| |
| // set the device ready bit |
| status = STATUS_DRDY_BIT; |
| |
| /* The error register must be set to 0x1 on start-up to |
| indicate that no diagnostic error was detected */ |
| cmdReg.error = 0x1; |
| } |
| |
| //// |
| // Utility functions |
| //// |
| |
| bool |
| IdeDisk::isDEVSelect() |
| { |
| return ctrl->isDiskSelected(this); |
| } |
| |
| Addr |
| IdeDisk::pciToDma(Addr pciAddr) |
| { |
| if (ctrl) |
| return ctrl->pciToDma(pciAddr); |
| else |
| panic("Access to unset controller!\n"); |
| } |
| |
| //// |
| // Device registers read/write |
| //// |
| |
| void |
| IdeDisk::readCommand(const Addr offset, int size, uint8_t *data) |
| { |
| if (offset == DATA_OFFSET) { |
| if (size == sizeof(uint16_t)) { |
| *(uint16_t *)data = cmdReg.data; |
| } else if (size == sizeof(uint32_t)) { |
| *(uint16_t *)data = cmdReg.data; |
| updateState(ACT_DATA_READ_SHORT); |
| *((uint16_t *)data + 1) = cmdReg.data; |
| } else { |
| panic("Data read of unsupported size %d.\n", size); |
| } |
| updateState(ACT_DATA_READ_SHORT); |
| return; |
| } |
| assert(size == sizeof(uint8_t)); |
| switch (offset) { |
| case ERROR_OFFSET: |
| *data = cmdReg.error; |
| break; |
| case NSECTOR_OFFSET: |
| *data = cmdReg.sec_count; |
| break; |
| case SECTOR_OFFSET: |
| *data = cmdReg.sec_num; |
| break; |
| case LCYL_OFFSET: |
| *data = cmdReg.cyl_low; |
| break; |
| case HCYL_OFFSET: |
| *data = cmdReg.cyl_high; |
| break; |
| case DRIVE_OFFSET: |
| *data = cmdReg.drive; |
| break; |
| case STATUS_OFFSET: |
| *data = status; |
| updateState(ACT_STAT_READ); |
| break; |
| default: |
| panic("Invalid IDE command register offset: %#x\n", offset); |
| } |
| DPRINTF(IdeDisk, "Read to disk at offset: %#x data %#x\n", offset, *data); |
| } |
| |
| void |
| IdeDisk::readControl(const Addr offset, int size, uint8_t *data) |
| { |
| assert(size == sizeof(uint8_t)); |
| *data = status; |
| if (offset != ALTSTAT_OFFSET) |
| panic("Invalid IDE control register offset: %#x\n", offset); |
| DPRINTF(IdeDisk, "Read to disk at offset: %#x data %#x\n", offset, *data); |
| } |
| |
| void |
| IdeDisk::writeCommand(const Addr offset, int size, const uint8_t *data) |
| { |
| if (offset == DATA_OFFSET) { |
| if (size == sizeof(uint16_t)) { |
| cmdReg.data = *(const uint16_t *)data; |
| } else if (size == sizeof(uint32_t)) { |
| cmdReg.data = *(const uint16_t *)data; |
| updateState(ACT_DATA_WRITE_SHORT); |
| cmdReg.data = *((const uint16_t *)data + 1); |
| } else { |
| panic("Data write of unsupported size %d.\n", size); |
| } |
| updateState(ACT_DATA_WRITE_SHORT); |
| return; |
| } |
| |
| assert(size == sizeof(uint8_t)); |
| switch (offset) { |
| case FEATURES_OFFSET: |
| break; |
| case NSECTOR_OFFSET: |
| cmdReg.sec_count = *data; |
| break; |
| case SECTOR_OFFSET: |
| cmdReg.sec_num = *data; |
| break; |
| case LCYL_OFFSET: |
| cmdReg.cyl_low = *data; |
| break; |
| case HCYL_OFFSET: |
| cmdReg.cyl_high = *data; |
| break; |
| case DRIVE_OFFSET: |
| cmdReg.drive = *data; |
| updateState(ACT_SELECT_WRITE); |
| break; |
| case COMMAND_OFFSET: |
| cmdReg.command = *data; |
| updateState(ACT_CMD_WRITE); |
| break; |
| default: |
| panic("Invalid IDE command register offset: %#x\n", offset); |
| } |
| DPRINTF(IdeDisk, "Write to disk at offset: %#x data %#x\n", offset, |
| (uint32_t)*data); |
| } |
| |
| void |
| IdeDisk::writeControl(const Addr offset, int size, const uint8_t *data) |
| { |
| if (offset != CONTROL_OFFSET) |
| panic("Invalid IDE control register offset: %#x\n", offset); |
| |
| if (*data & CONTROL_RST_BIT) { |
| // force the device into the reset state |
| devState = Device_Srst; |
| updateState(ACT_SRST_SET); |
| } else if (devState == Device_Srst && !(*data & CONTROL_RST_BIT)) { |
| updateState(ACT_SRST_CLEAR); |
| } |
| |
| nIENBit = *data & CONTROL_IEN_BIT; |
| |
| DPRINTF(IdeDisk, "Write to disk at offset: %#x data %#x\n", offset, |
| (uint32_t)*data); |
| } |
| |
| //// |
| // Perform DMA transactions |
| //// |
| |
| void |
| IdeDisk::doDmaTransfer() |
| { |
| if (dmaAborted) { |
| DPRINTF(IdeDisk, "DMA Aborted before reading PRD entry\n"); |
| updateState(ACT_CMD_ERROR); |
| return; |
| } |
| |
| if (dmaState != Dma_Transfer || devState != Transfer_Data_Dma) |
| panic("Inconsistent DMA transfer state: dmaState = %d devState = %d\n", |
| dmaState, devState); |
| |
| if (ctrl->dmaPending() || ctrl->drainState() != DrainState::Running) { |
| schedule(dmaTransferEvent, curTick() + DMA_BACKOFF_PERIOD); |
| return; |
| } else |
| ctrl->dmaRead(curPrdAddr, sizeof(PrdEntry_t), &dmaPrdReadEvent, |
| (uint8_t*)&curPrd.entry); |
| } |
| |
| void |
| IdeDisk::dmaPrdReadDone() |
| { |
| if (dmaAborted) { |
| DPRINTF(IdeDisk, "DMA Aborted while reading PRD entry\n"); |
| updateState(ACT_CMD_ERROR); |
| return; |
| } |
| |
| DPRINTF(IdeDisk, |
| "PRD: baseAddr:%#x (%#x) byteCount:%d (%d) eot:%#x sector:%d\n", |
| curPrd.getBaseAddr(), pciToDma(curPrd.getBaseAddr()), |
| curPrd.getByteCount(), (cmdBytesLeft/SectorSize), |
| curPrd.getEOT(), curSector); |
| |
| // the prd pointer has already been translated, so just do an increment |
| curPrdAddr = curPrdAddr + sizeof(PrdEntry_t); |
| |
| if (dmaRead) |
| doDmaDataRead(); |
| else |
| doDmaDataWrite(); |
| } |
| |
| void |
| IdeDisk::doDmaDataRead() |
| { |
| /** @todo we need to figure out what the delay actually will be */ |
| Tick totalDiskDelay = diskDelay + (curPrd.getByteCount() / SectorSize); |
| |
| DPRINTF(IdeDisk, "doDmaRead, diskDelay: %d totalDiskDelay: %d\n", |
| diskDelay, totalDiskDelay); |
| |
| schedule(dmaReadWaitEvent, curTick() + totalDiskDelay); |
| } |
| |
| IdeDisk:: |
| IdeDiskStats::IdeDiskStats(Stats::Group *parent) |
| : Stats::Group(parent, "IdeDisk"), |
| ADD_STAT(dmaReadFullPages, UNIT_COUNT, |
| "Number of full page size DMA reads (not PRD)."), |
| ADD_STAT(dmaReadBytes, UNIT_BYTE, |
| "Number of bytes transfered via DMA reads (not PRD)."), |
| ADD_STAT(dmaReadTxs, UNIT_COUNT, |
| "Number of DMA read transactions (not PRD)."), |
| ADD_STAT(dmaWriteFullPages, UNIT_COUNT, |
| "Number of full page size DMA writes."), |
| ADD_STAT(dmaWriteBytes, UNIT_BYTE, |
| "Number of bytes transfered via DMA writes."), |
| ADD_STAT(dmaWriteTxs, UNIT_COUNT, "Number of DMA write transactions.") |
| { |
| } |
| |
| void |
| IdeDisk::doDmaRead() |
| { |
| if (dmaAborted) { |
| DPRINTF(IdeDisk, "DMA Aborted in middle of Dma Read\n"); |
| if (dmaReadCG) |
| delete dmaReadCG; |
| dmaReadCG = NULL; |
| updateState(ACT_CMD_ERROR); |
| return; |
| } |
| |
| if (!dmaReadCG) { |
| // clear out the data buffer |
| memset(dataBuffer, 0, MAX_DMA_SIZE); |
| dmaReadCG = new ChunkGenerator(curPrd.getBaseAddr(), |
| curPrd.getByteCount(), chunkBytes); |
| |
| } |
| if (ctrl->dmaPending() || ctrl->drainState() != DrainState::Running) { |
| schedule(dmaReadWaitEvent, curTick() + DMA_BACKOFF_PERIOD); |
| return; |
| } else if (!dmaReadCG->done()) { |
| assert(dmaReadCG->complete() < MAX_DMA_SIZE); |
| ctrl->dmaRead(pciToDma(dmaReadCG->addr()), dmaReadCG->size(), |
| &dmaReadWaitEvent, dataBuffer + dmaReadCG->complete()); |
| ideDiskStats.dmaReadBytes += dmaReadCG->size(); |
| ideDiskStats.dmaReadTxs++; |
| if (dmaReadCG->size() == chunkBytes) |
| ideDiskStats.dmaReadFullPages++; |
| dmaReadCG->next(); |
| } else { |
| assert(dmaReadCG->done()); |
| delete dmaReadCG; |
| dmaReadCG = NULL; |
| dmaReadDone(); |
| } |
| } |
| |
| void |
| IdeDisk::dmaReadDone() |
| { |
| uint32_t bytesWritten = 0; |
| |
| // write the data to the disk image |
| for (bytesWritten = 0; bytesWritten < curPrd.getByteCount(); |
| bytesWritten += SectorSize) { |
| |
| cmdBytesLeft -= SectorSize; |
| writeDisk(curSector++, (uint8_t *)(dataBuffer + bytesWritten)); |
| } |
| |
| // check for the EOT |
| if (curPrd.getEOT()) { |
| assert(cmdBytesLeft == 0); |
| dmaState = Dma_Idle; |
| updateState(ACT_DMA_DONE); |
| } else { |
| doDmaTransfer(); |
| } |
| } |
| |
| void |
| IdeDisk::doDmaDataWrite() |
| { |
| /** @todo we need to figure out what the delay actually will be */ |
| Tick totalDiskDelay = diskDelay + (curPrd.getByteCount() / SectorSize); |
| uint32_t bytesRead = 0; |
| |
| DPRINTF(IdeDisk, "doDmaWrite, diskDelay: %d totalDiskDelay: %d\n", |
| diskDelay, totalDiskDelay); |
| |
| memset(dataBuffer, 0, MAX_DMA_SIZE); |
| assert(cmdBytesLeft <= MAX_DMA_SIZE); |
| while (bytesRead < curPrd.getByteCount()) { |
| readDisk(curSector++, (uint8_t *)(dataBuffer + bytesRead)); |
| bytesRead += SectorSize; |
| cmdBytesLeft -= SectorSize; |
| } |
| DPRINTF(IdeDisk, "doDmaWrite, bytesRead: %d cmdBytesLeft: %d\n", |
| bytesRead, cmdBytesLeft); |
| |
| schedule(dmaWriteWaitEvent, curTick() + totalDiskDelay); |
| } |
| |
| void |
| IdeDisk::doDmaWrite() |
| { |
| if (dmaAborted) { |
| DPRINTF(IdeDisk, "DMA Aborted while doing DMA Write\n"); |
| if (dmaWriteCG) |
| delete dmaWriteCG; |
| dmaWriteCG = NULL; |
| updateState(ACT_CMD_ERROR); |
| return; |
| } |
| if (!dmaWriteCG) { |
| // clear out the data buffer |
| dmaWriteCG = new ChunkGenerator(curPrd.getBaseAddr(), |
| curPrd.getByteCount(), chunkBytes); |
| } |
| if (ctrl->dmaPending() || ctrl->drainState() != DrainState::Running) { |
| schedule(dmaWriteWaitEvent, curTick() + DMA_BACKOFF_PERIOD); |
| DPRINTF(IdeDisk, "doDmaWrite: rescheduling\n"); |
| return; |
| } else if (!dmaWriteCG->done()) { |
| assert(dmaWriteCG->complete() < MAX_DMA_SIZE); |
| ctrl->dmaWrite(pciToDma(dmaWriteCG->addr()), dmaWriteCG->size(), |
| &dmaWriteWaitEvent, dataBuffer + dmaWriteCG->complete()); |
| DPRINTF(IdeDisk, "doDmaWrite: not done curPrd byte count %d, eot %#x\n", |
| curPrd.getByteCount(), curPrd.getEOT()); |
| ideDiskStats.dmaWriteBytes += dmaWriteCG->size(); |
| ideDiskStats.dmaWriteTxs++; |
| if (dmaWriteCG->size() == chunkBytes) |
| ideDiskStats.dmaWriteFullPages++; |
| dmaWriteCG->next(); |
| } else { |
| DPRINTF(IdeDisk, "doDmaWrite: done curPrd byte count %d, eot %#x\n", |
| curPrd.getByteCount(), curPrd.getEOT()); |
| assert(dmaWriteCG->done()); |
| delete dmaWriteCG; |
| dmaWriteCG = NULL; |
| dmaWriteDone(); |
| } |
| } |
| |
| void |
| IdeDisk::dmaWriteDone() |
| { |
| DPRINTF(IdeDisk, "doWriteDone: curPrd byte count %d, eot %#x cmd bytes left:%d\n", |
| curPrd.getByteCount(), curPrd.getEOT(), cmdBytesLeft); |
| // check for the EOT |
| if (curPrd.getEOT()) { |
| assert(cmdBytesLeft == 0); |
| dmaState = Dma_Idle; |
| updateState(ACT_DMA_DONE); |
| } else { |
| doDmaTransfer(); |
| } |
| } |
| |
| //// |
| // Disk utility routines |
| /// |
| |
| void |
| IdeDisk::readDisk(uint32_t sector, uint8_t *data) |
| { |
| uint32_t bytesRead = image->read(data, sector); |
| |
| if (bytesRead != SectorSize) |
| panic("Can't read from %s. Only %d of %d read. errno=%d\n", |
| name(), bytesRead, SectorSize, errno); |
| } |
| |
| void |
| IdeDisk::writeDisk(uint32_t sector, uint8_t *data) |
| { |
| uint32_t bytesWritten = image->write(data, sector); |
| |
| if (bytesWritten != SectorSize) |
| panic("Can't write to %s. Only %d of %d written. errno=%d\n", |
| name(), bytesWritten, SectorSize, errno); |
| } |
| |
| //// |
| // Setup and handle commands |
| //// |
| |
| void |
| IdeDisk::startDma(const uint32_t &prdTableBase) |
| { |
| if (dmaState != Dma_Start) |
| panic("Inconsistent DMA state, should be in Dma_Start!\n"); |
| |
| if (devState != Transfer_Data_Dma) |
| panic("Inconsistent device state for DMA start!\n"); |
| |
| // PRD base address is given by bits 31:2 |
| curPrdAddr = pciToDma((Addr)(prdTableBase & ~ULL(0x3))); |
| |
| dmaState = Dma_Transfer; |
| |
| // schedule dma transfer (doDmaTransfer) |
| schedule(dmaTransferEvent, curTick() + 1); |
| } |
| |
| void |
| IdeDisk::abortDma() |
| { |
| if (dmaState == Dma_Idle) |
| panic("Inconsistent DMA state, should be Start or Transfer!"); |
| |
| if (devState != Transfer_Data_Dma && devState != Prepare_Data_Dma) |
| panic("Inconsistent device state, should be Transfer or Prepare!\n"); |
| |
| updateState(ACT_CMD_ERROR); |
| } |
| |
| void |
| IdeDisk::startCommand() |
| { |
| DevAction_t action = ACT_NONE; |
| uint32_t size = 0; |
| dmaRead = false; |
| |
| // Decode commands |
| switch (cmdReg.command) { |
| // Supported non-data commands |
| case WDSF_READ_NATIVE_MAX: |
| size = (uint32_t)image->size() - 1; |
| cmdReg.sec_num = (size & 0xff); |
| cmdReg.cyl_low = ((size & 0xff00) >> 8); |
| cmdReg.cyl_high = ((size & 0xff0000) >> 16); |
| cmdReg.head = ((size & 0xf000000) >> 24); |
| |
| devState = Command_Execution; |
| action = ACT_CMD_COMPLETE; |
| break; |
| |
| case WDCC_RECAL: |
| case WDCC_IDP: |
| case WDCC_STANDBY_IMMED: |
| case WDCC_FLUSHCACHE: |
| case WDSF_VERIFY: |
| case WDSF_SEEK: |
| case SET_FEATURES: |
| case WDCC_SETMULTI: |
| case WDCC_IDLE: |
| devState = Command_Execution; |
| action = ACT_CMD_COMPLETE; |
| break; |
| |
| // Supported PIO data-in commands |
| case WDCC_IDENTIFY: |
| case ATAPI_IDENTIFY_DEVICE: |
| cmdBytes = cmdBytesLeft = sizeof(struct ataparams); |
| devState = Prepare_Data_In; |
| action = ACT_DATA_READY; |
| break; |
| |
| case WDCC_READMULTI: |
| case WDCC_READ: |
| if (!(cmdReg.drive & DRIVE_LBA_BIT)) |
| panic("Attempt to perform CHS access, only supports LBA\n"); |
| |
| if (cmdReg.sec_count == 0) |
| cmdBytes = cmdBytesLeft = (256 * SectorSize); |
| else |
| cmdBytes = cmdBytesLeft = (cmdReg.sec_count * SectorSize); |
| |
| curSector = getLBABase(); |
| |
| /** @todo make this a scheduled event to simulate disk delay */ |
| devState = Prepare_Data_In; |
| action = ACT_DATA_READY; |
| break; |
| |
| // Supported PIO data-out commands |
| case WDCC_WRITEMULTI: |
| case WDCC_WRITE: |
| if (!(cmdReg.drive & DRIVE_LBA_BIT)) |
| panic("Attempt to perform CHS access, only supports LBA\n"); |
| |
| if (cmdReg.sec_count == 0) |
| cmdBytes = cmdBytesLeft = (256 * SectorSize); |
| else |
| cmdBytes = cmdBytesLeft = (cmdReg.sec_count * SectorSize); |
| DPRINTF(IdeDisk, "Setting cmdBytesLeft to %d\n", cmdBytesLeft); |
| curSector = getLBABase(); |
| |
| devState = Prepare_Data_Out; |
| action = ACT_DATA_READY; |
| break; |
| |
| // Supported DMA commands |
| case WDCC_WRITEDMA: |
| dmaRead = true; // a write to the disk is a DMA read from memory |
| M5_FALLTHROUGH; |
| case WDCC_READDMA: |
| if (!(cmdReg.drive & DRIVE_LBA_BIT)) |
| panic("Attempt to perform CHS access, only supports LBA\n"); |
| |
| if (cmdReg.sec_count == 0) |
| cmdBytes = cmdBytesLeft = (256 * SectorSize); |
| else |
| cmdBytes = cmdBytesLeft = (cmdReg.sec_count * SectorSize); |
| DPRINTF(IdeDisk, "Setting cmdBytesLeft to %d in readdma\n", cmdBytesLeft); |
| |
| curSector = getLBABase(); |
| |
| devState = Prepare_Data_Dma; |
| action = ACT_DMA_READY; |
| break; |
| |
| default: |
| panic("Unsupported ATA command: %#x\n", cmdReg.command); |
| } |
| |
| if (action != ACT_NONE) { |
| // set the BSY bit |
| status |= STATUS_BSY_BIT; |
| // clear the DRQ bit |
| status &= ~STATUS_DRQ_BIT; |
| // clear the DF bit |
| status &= ~STATUS_DF_BIT; |
| |
| updateState(action); |
| } |
| } |
| |
| //// |
| // Handle setting and clearing interrupts |
| //// |
| |
| void |
| IdeDisk::intrPost() |
| { |
| DPRINTF(IdeDisk, "Posting Interrupt\n"); |
| if (intrPending) |
| panic("Attempt to post an interrupt with one pending\n"); |
| |
| intrPending = true; |
| |
| // talk to controller to set interrupt |
| if (ctrl) { |
| ctrl->intrPost(); |
| } |
| } |
| |
| void |
| IdeDisk::intrClear() |
| { |
| DPRINTF(IdeDisk, "Clearing Interrupt\n"); |
| if (!intrPending) |
| panic("Attempt to clear a non-pending interrupt\n"); |
| |
| intrPending = false; |
| |
| // talk to controller to clear interrupt |
| if (ctrl) |
| ctrl->intrClear(); |
| } |
| |
| //// |
| // Manage the device internal state machine |
| //// |
| |
| void |
| IdeDisk::updateState(DevAction_t action) |
| { |
| switch (devState) { |
| case Device_Srst: |
| if (action == ACT_SRST_SET) { |
| // set the BSY bit |
| status |= STATUS_BSY_BIT; |
| } else if (action == ACT_SRST_CLEAR) { |
| // clear the BSY bit |
| status &= ~STATUS_BSY_BIT; |
| |
| // reset the device state |
| reset(devID); |
| } |
| break; |
| |
| case Device_Idle_S: |
| if (action == ACT_SELECT_WRITE && !isDEVSelect()) { |
| devState = Device_Idle_NS; |
| } else if (action == ACT_CMD_WRITE) { |
| startCommand(); |
| } |
| |
| break; |
| |
| case Device_Idle_SI: |
| if (action == ACT_SELECT_WRITE && !isDEVSelect()) { |
| devState = Device_Idle_NS; |
| intrClear(); |
| } else if (action == ACT_STAT_READ || isIENSet()) { |
| devState = Device_Idle_S; |
| intrClear(); |
| } else if (action == ACT_CMD_WRITE) { |
| intrClear(); |
| startCommand(); |
| } |
| |
| break; |
| |
| case Device_Idle_NS: |
| if (action == ACT_SELECT_WRITE && isDEVSelect()) { |
| if (!isIENSet() && intrPending) { |
| devState = Device_Idle_SI; |
| intrPost(); |
| } |
| if (isIENSet() || !intrPending) { |
| devState = Device_Idle_S; |
| } |
| } |
| break; |
| |
| case Command_Execution: |
| if (action == ACT_CMD_COMPLETE) { |
| // clear the BSY bit |
| setComplete(); |
| |
| if (!isIENSet()) { |
| devState = Device_Idle_SI; |
| intrPost(); |
| } else { |
| devState = Device_Idle_S; |
| } |
| } |
| break; |
| |
| case Prepare_Data_In: |
| if (action == ACT_CMD_ERROR) { |
| // clear the BSY bit |
| setComplete(); |
| |
| if (!isIENSet()) { |
| devState = Device_Idle_SI; |
| intrPost(); |
| } else { |
| devState = Device_Idle_S; |
| } |
| } else if (action == ACT_DATA_READY) { |
| // clear the BSY bit |
| status &= ~STATUS_BSY_BIT; |
| // set the DRQ bit |
| status |= STATUS_DRQ_BIT; |
| |
| // copy the data into the data buffer |
| if (cmdReg.command == WDCC_IDENTIFY || |
| cmdReg.command == ATAPI_IDENTIFY_DEVICE) { |
| // Reset the drqBytes for this block |
| drqBytesLeft = sizeof(struct ataparams); |
| |
| memcpy((void *)dataBuffer, (void *)&driveID, |
| sizeof(struct ataparams)); |
| } else { |
| // Reset the drqBytes for this block |
| drqBytesLeft = SectorSize; |
| |
| readDisk(curSector++, dataBuffer); |
| } |
| |
| // put the first two bytes into the data register |
| memcpy((void *)&cmdReg.data, (void *)dataBuffer, |
| sizeof(uint16_t)); |
| |
| if (!isIENSet()) { |
| devState = Data_Ready_INTRQ_In; |
| intrPost(); |
| } else { |
| devState = Transfer_Data_In; |
| } |
| } |
| break; |
| |
| case Data_Ready_INTRQ_In: |
| if (action == ACT_STAT_READ) { |
| devState = Transfer_Data_In; |
| intrClear(); |
| } |
| break; |
| |
| case Transfer_Data_In: |
| if (action == ACT_DATA_READ_BYTE || action == ACT_DATA_READ_SHORT) { |
| if (action == ACT_DATA_READ_BYTE) { |
| panic("DEBUG: READING DATA ONE BYTE AT A TIME!\n"); |
| } else { |
| drqBytesLeft -= 2; |
| cmdBytesLeft -= 2; |
| |
| // copy next short into data registers |
| if (drqBytesLeft) |
| memcpy((void *)&cmdReg.data, |
| (void *)&dataBuffer[SectorSize - drqBytesLeft], |
| sizeof(uint16_t)); |
| } |
| |
| if (drqBytesLeft == 0) { |
| if (cmdBytesLeft == 0) { |
| // Clear the BSY bit |
| setComplete(); |
| devState = Device_Idle_S; |
| } else { |
| devState = Prepare_Data_In; |
| // set the BSY_BIT |
| status |= STATUS_BSY_BIT; |
| // clear the DRQ_BIT |
| status &= ~STATUS_DRQ_BIT; |
| |
| /** @todo change this to a scheduled event to simulate |
| disk delay */ |
| updateState(ACT_DATA_READY); |
| } |
| } |
| } |
| break; |
| |
| case Prepare_Data_Out: |
| if (action == ACT_CMD_ERROR || cmdBytesLeft == 0) { |
| // clear the BSY bit |
| setComplete(); |
| |
| if (!isIENSet()) { |
| devState = Device_Idle_SI; |
| intrPost(); |
| } else { |
| devState = Device_Idle_S; |
| } |
| } else if (action == ACT_DATA_READY && cmdBytesLeft != 0) { |
| // clear the BSY bit |
| status &= ~STATUS_BSY_BIT; |
| // set the DRQ bit |
| status |= STATUS_DRQ_BIT; |
| |
| // clear the data buffer to get it ready for writes |
| memset(dataBuffer, 0, MAX_DMA_SIZE); |
| |
| // reset the drqBytes for this block |
| drqBytesLeft = SectorSize; |
| |
| if (cmdBytesLeft == cmdBytes || isIENSet()) { |
| devState = Transfer_Data_Out; |
| } else { |
| devState = Data_Ready_INTRQ_Out; |
| intrPost(); |
| } |
| } |
| break; |
| |
| case Data_Ready_INTRQ_Out: |
| if (action == ACT_STAT_READ) { |
| devState = Transfer_Data_Out; |
| intrClear(); |
| } |
| break; |
| |
| case Transfer_Data_Out: |
| if (action == ACT_DATA_WRITE_BYTE || |
| action == ACT_DATA_WRITE_SHORT) { |
| |
| if (action == ACT_DATA_READ_BYTE) { |
| panic("DEBUG: WRITING DATA ONE BYTE AT A TIME!\n"); |
| } else { |
| // copy the latest short into the data buffer |
| memcpy((void *)&dataBuffer[SectorSize - drqBytesLeft], |
| (void *)&cmdReg.data, |
| sizeof(uint16_t)); |
| |
| drqBytesLeft -= 2; |
| cmdBytesLeft -= 2; |
| } |
| |
| if (drqBytesLeft == 0) { |
| // copy the block to the disk |
| writeDisk(curSector++, dataBuffer); |
| |
| // set the BSY bit |
| status |= STATUS_BSY_BIT; |
| // set the seek bit |
| status |= STATUS_SEEK_BIT; |
| // clear the DRQ bit |
| status &= ~STATUS_DRQ_BIT; |
| |
| devState = Prepare_Data_Out; |
| |
| /** @todo change this to a scheduled event to simulate |
| disk delay */ |
| updateState(ACT_DATA_READY); |
| } |
| } |
| break; |
| |
| case Prepare_Data_Dma: |
| if (action == ACT_CMD_ERROR) { |
| // clear the BSY bit |
| setComplete(); |
| |
| if (!isIENSet()) { |
| devState = Device_Idle_SI; |
| intrPost(); |
| } else { |
| devState = Device_Idle_S; |
| } |
| } else if (action == ACT_DMA_READY) { |
| // clear the BSY bit |
| status &= ~STATUS_BSY_BIT; |
| // set the DRQ bit |
| status |= STATUS_DRQ_BIT; |
| |
| devState = Transfer_Data_Dma; |
| |
| if (dmaState != Dma_Idle) |
| panic("Inconsistent DMA state, should be Dma_Idle\n"); |
| |
| dmaState = Dma_Start; |
| // wait for the write to the DMA start bit |
| } |
| break; |
| |
| case Transfer_Data_Dma: |
| if (action == ACT_CMD_ERROR) { |
| dmaAborted = true; |
| devState = Device_Dma_Abort; |
| } else if (action == ACT_DMA_DONE) { |
| // clear the BSY bit |
| setComplete(); |
| // set the seek bit |
| status |= STATUS_SEEK_BIT; |
| // clear the controller state for DMA transfer |
| ctrl->setDmaComplete(this); |
| |
| if (!isIENSet()) { |
| devState = Device_Idle_SI; |
| intrPost(); |
| } else { |
| devState = Device_Idle_S; |
| } |
| } |
| break; |
| |
| case Device_Dma_Abort: |
| if (action == ACT_CMD_ERROR) { |
| setComplete(); |
| status |= STATUS_SEEK_BIT; |
| ctrl->setDmaComplete(this); |
| dmaAborted = false; |
| dmaState = Dma_Idle; |
| |
| if (!isIENSet()) { |
| devState = Device_Idle_SI; |
| intrPost(); |
| } else { |
| devState = Device_Idle_S; |
| } |
| } else { |
| DPRINTF(IdeDisk, "Disk still busy aborting previous DMA command\n"); |
| } |
| break; |
| |
| default: |
| panic("Unknown IDE device state: %#x\n", devState); |
| } |
| } |
| |
| void |
| IdeDisk::serialize(CheckpointOut &cp) const |
| { |
| // Check all outstanding events to see if they are scheduled |
| // these are all mutually exclusive |
| Tick reschedule = 0; |
| Events_t event = None; |
| |
| int eventCount = 0; |
| |
| if (dmaTransferEvent.scheduled()) { |
| reschedule = dmaTransferEvent.when(); |
| event = Transfer; |
| eventCount++; |
| } |
| if (dmaReadWaitEvent.scheduled()) { |
| reschedule = dmaReadWaitEvent.when(); |
| event = ReadWait; |
| eventCount++; |
| } |
| if (dmaWriteWaitEvent.scheduled()) { |
| reschedule = dmaWriteWaitEvent.when(); |
| event = WriteWait; |
| eventCount++; |
| } |
| if (dmaPrdReadEvent.scheduled()) { |
| reschedule = dmaPrdReadEvent.when(); |
| event = PrdRead; |
| eventCount++; |
| } |
| if (dmaReadEvent.scheduled()) { |
| reschedule = dmaReadEvent.when(); |
| event = DmaRead; |
| eventCount++; |
| } |
| if (dmaWriteEvent.scheduled()) { |
| reschedule = dmaWriteEvent.when(); |
| event = DmaWrite; |
| eventCount++; |
| } |
| |
| assert(eventCount <= 1); |
| |
| SERIALIZE_SCALAR(reschedule); |
| SERIALIZE_ENUM(event); |
| |
| // Serialize device registers |
| SERIALIZE_SCALAR(cmdReg.data); |
| SERIALIZE_SCALAR(cmdReg.sec_count); |
| SERIALIZE_SCALAR(cmdReg.sec_num); |
| SERIALIZE_SCALAR(cmdReg.cyl_low); |
| SERIALIZE_SCALAR(cmdReg.cyl_high); |
| SERIALIZE_SCALAR(cmdReg.drive); |
| SERIALIZE_SCALAR(cmdReg.command); |
| SERIALIZE_SCALAR(status); |
| SERIALIZE_SCALAR(nIENBit); |
| SERIALIZE_SCALAR(devID); |
| |
| // Serialize the PRD related information |
| SERIALIZE_SCALAR(curPrd.entry.baseAddr); |
| SERIALIZE_SCALAR(curPrd.entry.byteCount); |
| SERIALIZE_SCALAR(curPrd.entry.endOfTable); |
| SERIALIZE_SCALAR(curPrdAddr); |
| |
| /** @todo need to serialized chunk generator stuff!! */ |
| // Serialize current transfer related information |
| SERIALIZE_SCALAR(cmdBytesLeft); |
| SERIALIZE_SCALAR(cmdBytes); |
| SERIALIZE_SCALAR(drqBytesLeft); |
| SERIALIZE_SCALAR(curSector); |
| SERIALIZE_SCALAR(dmaRead); |
| SERIALIZE_SCALAR(intrPending); |
| SERIALIZE_SCALAR(dmaAborted); |
| SERIALIZE_ENUM(devState); |
| SERIALIZE_ENUM(dmaState); |
| SERIALIZE_ARRAY(dataBuffer, MAX_DMA_SIZE); |
| } |
| |
| void |
| IdeDisk::unserialize(CheckpointIn &cp) |
| { |
| // Reschedule events that were outstanding |
| // these are all mutually exclusive |
| Tick reschedule = 0; |
| Events_t event = None; |
| |
| UNSERIALIZE_SCALAR(reschedule); |
| UNSERIALIZE_ENUM(event); |
| |
| switch (event) { |
| case None : break; |
| case Transfer : schedule(dmaTransferEvent, reschedule); break; |
| case ReadWait : schedule(dmaReadWaitEvent, reschedule); break; |
| case WriteWait : schedule(dmaWriteWaitEvent, reschedule); break; |
| case PrdRead : schedule(dmaPrdReadEvent, reschedule); break; |
| case DmaRead : schedule(dmaReadEvent, reschedule); break; |
| case DmaWrite : schedule(dmaWriteEvent, reschedule); break; |
| } |
| |
| // Unserialize device registers |
| UNSERIALIZE_SCALAR(cmdReg.data); |
| UNSERIALIZE_SCALAR(cmdReg.sec_count); |
| UNSERIALIZE_SCALAR(cmdReg.sec_num); |
| UNSERIALIZE_SCALAR(cmdReg.cyl_low); |
| UNSERIALIZE_SCALAR(cmdReg.cyl_high); |
| UNSERIALIZE_SCALAR(cmdReg.drive); |
| UNSERIALIZE_SCALAR(cmdReg.command); |
| UNSERIALIZE_SCALAR(status); |
| UNSERIALIZE_SCALAR(nIENBit); |
| UNSERIALIZE_SCALAR(devID); |
| |
| // Unserialize the PRD related information |
| UNSERIALIZE_SCALAR(curPrd.entry.baseAddr); |
| UNSERIALIZE_SCALAR(curPrd.entry.byteCount); |
| UNSERIALIZE_SCALAR(curPrd.entry.endOfTable); |
| UNSERIALIZE_SCALAR(curPrdAddr); |
| |
| /** @todo need to serialized chunk generator stuff!! */ |
| // Unserialize current transfer related information |
| UNSERIALIZE_SCALAR(cmdBytes); |
| UNSERIALIZE_SCALAR(cmdBytesLeft); |
| UNSERIALIZE_SCALAR(drqBytesLeft); |
| UNSERIALIZE_SCALAR(curSector); |
| UNSERIALIZE_SCALAR(dmaRead); |
| UNSERIALIZE_SCALAR(intrPending); |
| UNSERIALIZE_SCALAR(dmaAborted); |
| UNSERIALIZE_ENUM(devState); |
| UNSERIALIZE_ENUM(dmaState); |
| UNSERIALIZE_ARRAY(dataBuffer, MAX_DMA_SIZE); |
| } |
